FrontHandlebars, F forks, headlights, etc.

【Front Tire】

【LOADSTAR TIRE 4.00-18】

◯A classic watermelon pattern, a vintage style tire with height.

【Headlight】

“5.75 inch Bates Light Black Body/Chrome Rim”

“Bottom Mount Light Stay II“

〇A headlight stay that suits the chopper style well with its moderate height and protrusion. (5.75 inch Bates Light Set II SR400/SR500)

【Handle/Handle Area】

“Narrow Drag Bar Handle”

〇A narrow flat handle with a short clamp section.

“Flanders Replica Riser 2.5 Inch“

〇A simple drag bar that doesn’t disrupt the line, set in a position that doesn’t tire easily.

“Amal type throttle holder, general purpose (for 7/8″)“

◯The controls are a standard clean finish from 2%ER.

“Handle Lock Weld On Kit“

〇It is bolted on to the less noticeable and easy-to-operate lower part of the stem for installation.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach an M10 millimeter blinker to the frame bottom.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

CenterTank, oil tank, seat, step, muffler etc.

• The owner’s preferred narrow Mustang tank. It’s a gas tank that’s difficult to naturally attach to the thick frame of the SR due to its narrow width and small capacity, but it was well attached with minimal bottom plate processing. The paint is green metallic single color as specified by the owner.

【Muffler】

◯ The muffler is a simple layout drag pipe close to the car body. A convenient manufacturing kit is used at the root of the mouthpiece for one-off production. Ripple processing is added near the end as an accent.

“One-off Pipe Manufacturing Exhaust Pipe Flange Set”

Custom Exhaust Fabrication Ripple Pipe, 45mm (1-3/4″) Diameter

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and the position extremely less tiring.

【Seat】

〇With a spring-loaded solo saddle seat, you can mitigate the impact from the road surface and set the mounting angle well to ride surprisingly comfortably.

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

〇A mount kit that is easy to attach mainly to custom frames. You can also change the lever ratio and create a good cushioning effect.

【Electrical Equipment】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500“

〇All electrical components except for the CDI are consolidated at the rear of the engine crankcase. It is easily accessible from either side of the vehicle and has good maintainability. There is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without any problem even with LED turn signals. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇Easy to operate even while riding, welded on the lower left of the seat.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(5cm Long)

〇As the name suggests, this is a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to a rigid line. You can revert to a swing arm/rear shock specification during vehicle inspection or when changing styles. This extension process ensures a wider seating area, making it easier to distribute weight and making riding more comfortable.

【Rear Tire】

“Roadster 4.50-18 Tire”

〇The rear wheel is a standard 18-inch, with a selected vintage style, watermelon pattern classical tire.

【Rear Fender】

“5-Inch Custom Rib Fender – Steel Material“

“Reinforcement Back Plate for 5-Inch Rib Fender“

〇To prevent cracks and damage caused by minor vibrations of the SR, or the sway caused by the weight of the sissy bar, we attach it with optimal reinforcement on the backside.

【Tail Lamp】

“69 tail type3“

【Sissy Bar】

〇We made the one-off sissy bar as simple and smart as possible.

【RearTurn Signal】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style turn signal.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto the hardtail. Used as a base for the turn signal.

【Drive System】

『Rear sprocket SR400/500 428-56 』

〇An affordable and durable replacement sprocket.