FrontHandlebars, F forks, headlights, etc.

【Front Fork】

〇The fork bottom case is finished with smoothing & polish.

【Front Wheel】

“H-shape aluminum rim SR Front, one size up“

◯High precision RK. With one size up rim width from the normal rim, it has high accent effect along with increased rigidity.

【Front Tire】

“LOADSTAR4.00-18”

〇A classic watermelon pattern, a vintage style tire with height.

【Headlight】

“5.75 inch Bates Light Black Body/Plated Rim”

“SR Bottom Mount Light Stay”

〇A classic headlight that fits well with the SR’s vehicle size and fork width. It is mounted with a headlight stay that brings it closer to the vehicle body.

【Handle/Handle Surroundings】

“Ace Bar Type1”

◯Extremely simple, but the droop angle, bar length, etc. are the best handle for orthodox cafe racer style.

“Amal type throttle holder, general purpose (for 7/8″)”

“Amal type slot wire 900mm ’88~’08”

“Brake wire/100mm 200mm 300mm 600mm SR400/500 #SR400/500”

“Clutch wire/300mm 200mm 100mm standard SR400/500 ALL YEARS”

〇Simple throttle with each cable used.

“MOTOR ROCK Decompression lever”

〇Engine direct decomp lever to simplify the handle area. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose”

〇A classic among classics. A chopper style blinker.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4”

“Universal Speedometer Stay”

〇Mounted on the left front side of the gas tank, it is inconspicuous and has high visibility.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“One-off pipe production exhaust flange set for SR”

〇A one-off made using a convenient manufacturing kit for the root mouthpiece.

“Universal Stainless Steel Trumpet Muffler”

〇High-quality stainless steel muffler made in Japan.

【Gas Tank Installation】

“Narrow Sportster Tank for Manufacturing”

“Welding nut non-through M8 2p”

〇Drill a hole in the gas tank body and insert it for welding. It is non-penetrating so it does not leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p”

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p”

〇Used for rear gas tank installation. This also enlarges the hole diameter and uses it as a rubber mount.

【Electrical】

“IC blinker relay wide range specification”

〇A wide-range turn signal relay that can be used without difficulty even for LED turn signals. It can also be used as a repro for the original relay.

“Battery Lesser”

〇This is a battery-less kit that we manufacture in Japan.

“Custom Ignition Switch Weld On Kit General Purpose”

〇Easy to operate even while riding, welded to the lower left of the seat.

【Engine Area】

“Breather filter SR400/500”

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19”

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Shock】

“280mm Low Down Suspension] G-SUSPENSION280 [Chrome] General-purpose #SR400/500”

〇Rear shock with about 4cm down. It moves well among the low-down suspensions.

【Rear Wheel】

“H aluminum rim SR rear, one size up”

◯Rear wheel that makes a big accent visually. The wheel hub is drilled, and the drum panel is dummy air scoop processed.

【Rear Tire】

“LOADSTAR TIRE 4.50-18”

〇A standard watermelon pattern in vintage style. It’s a rear tire with height and volume.

【Rear Fender】

“Plain Aluminum Rear Fender with 120mm Width”

◯A universal aluminum fender with the same specs as vintage British bikes (such as Triumph and BSA).

【Rear Turn Signal】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose”

〇A classic among classics. A chopper-style turn signal.

【Drive System】

“Rear sprocket SR400/500 428-56 ”

〇A durable and affordable replacement sprocket.

“O-ring chain 428-130L”

〇A replacement drive chain with built-in O-rings.