Home » #98 SR400

#98 SR400

2015.9.9

Custom Bike

#98 SR400Custom Report

Slim and tight, in the style of a chopped cafe racer.

Even when a large owner rides it, the bike doesn’t look small. The swing arm has been extended by 5cm and the rear wheel has been enlarged to 16 inches.

Cookie consent is required to display this video.

Cookie Settings

Custom List

FrontHandlebars, F forks, headlights, etc.

【Front Wheel】

“2%er Front Wheel Aluminum Hub Cap Starburst Type [SR400/500]“

◯A hubcap that adds a classical accent.

【LOADSTAR TIRE 4.00-18】

◯A classic watermelon pattern, a vintage style tire with height.

【Front Fender】

◯The front fender is a one-off made of stainless steel. It was made to fit the tire height with minimal clearance.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“Slip-On Trumpet Muffler”

〇A classical trumpet muffler that is slip-on mounted on a normal exhaust pipe. It is a high-quality stainless muffler made in Japan, with a focus on sound quality.

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.

【Seat】

” Slim Double Seat Bates Type Vertical Roll for SR400/500“

〇The narrow seat that fits within the frame width is an original vertical type that focuses on comfort. It matches well with both slim and normal tanks.

【Electrical Equipment】

“Brat Style Electrical Plate“

〇A simple electrical plate that makes it easy to organize harnesses and electrical components.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can handle 1-150 watts and can be used without difficulty even with LED turn signals. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇A battery-less kit made in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇The main key, which is originally on the top bridge, is welded to the lower left of the seat for easy operation even while riding.

【Gasoline Tank Installation】

◯ The gas tank, which becomes the face of the slim upper body chop cafe style, is diverted from Honda CB50. It is installed by processing the bottom plate of the tunnel.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇A filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

• The frame end is looped. The swing arm is extended by 5cm, lowered, and the rear area is converted to 16 inches.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇A kit that matches the size of a typical Harley and adds impact.

【Rear Subframe】

“Loop Frame for SR400/500 and Others“

◯Produced to allow for the interchangeability of solo seats and double seats. It was made simple in combination with a short fender.

【Rear Shock】

“280mm G-Suspension/Chrome”

〇A rear shock that is about 4cm lower. By relocating the shock mount pivot on the swingarm side to the front, it is set to cushion more comfortably and smoothly.

【Rear Turn Signal】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style turn signal.

『Rear Bottom Mount Turn Signal Stay』