#183 SR400Custom Report

“A Hardtail SR400 custom made to the order of ‘A Badass Chopper’.

Not only a custom, but also an engine O/H, this was a vehicle brought in by a privateer customer who enjoys it himself. This is a vehicle that was requested to be brought in to make it even easier to ride and even cooler than the limits of his own work. At the time of bringing in, the original gas tank and handle were left as they were, and a hardtail kit was incorporated into the rear to change to a simple rigid frame, and the front fork was extended.

The rear fender, sissy bar, muffler, etc. were made one-off to form a chopper-style silhouette, and it was finished with a paint job by the atmospheric ‘BACON‘.

As the owner travels a considerable distance on a single tour, and is tall at 180cm, the position was carefully decided. The hardtail kit is a 13cm extended long type, so it’s not cramped and has a relaxed seat position, and the pullback handle helps support the upper body weight during acceleration with a pillion pad.

Furthermore, we decided to use a mid-forward control kit that moves the step position 120mm forward, which is recommended for taller people, so that each joint bends nicely and becomes a chopper-like riding posture.

The seat spring is determined by the owner’s weight, and compared to the hard short suspension at the time of bringing in, it is finished with a much easier position and cushioning.

 

【 The condition of the vehicle at the time of bringing in is here 】


“ Click here for the blog article on the production process, fork extension, and hardtail kit installation ”

 

“ Click here for the blog article on one-off production of mufflers and sissy bars, etc. ”


【 Movie of the right side of the vehicle 】

Cookie consent is required to display this video.

 

【 Movie of the left side of the vehicle 】

Cookie consent is required to display this video.

 

【 Movie of the entire vehicle and a light test run 】

Cookie consent is required to display this video.

Custom List

FrontHandlebars, F forks, headlights, etc.

Front Fork Area

2%er 15cm long Joints for Front Fork (pair) [SR400/500]

〇High-quality stainless steel fork joint.

SR400/500 15cm long inner tube kit

〇A fork tube kit that allows you to extend the front more safely.

2%er Tweak Bar (front stabilizer) [SR 400/500]

〇A stabilizer that is extremely effective in correcting the handling that tends to lag one beat behind with the extended fork.


Front Tire

“SHINKO flute 3.00-18”

〇A street tire with a vertical groove design. It helps to lighten the handling that tends to become heavy when long forks are used. It is a small, rounded 3.00 size.


Handle/Handle Area

Amal type throttle holder, general purpose (for 7/8″)

◯The handle is left as it is when brought in, and it is simplified by miniaturizing the switch, etc.


Handle Lock Weld On Kit

● It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.


Turn Signal

Diamond Winker Chrome 4pcs SET General Purpose

Diamond Turn Signal Stay


Speedometer

Mechanical Speedometer 60mm Black Panel 1:4

Universal Speedometer Stay

〇Mounted on the left front side of the gasoline tank, which is inconspicuous and has high visibility.


CenterTank, oil tank, seat, step, muffler etc.

Muffler

“Exhaust Pipe Flange Set for One-Off Pipe Production”

〇Using a convenient production kit for the base mouthpiece, one-off production. A turn-out drag pipe muffler that gives a more chopper-like atmosphere.

Custom Exhaust Fabrication Ripple Pipe, 45mm (1-3/4″) Diameter

◯Used in two places.

Low Pass Baffle

◯The “Low Pass Baffle”, which narrows the high tones and approaches a torqueful characteristic, is incorporated in the middle, resulting in a pleasant good sound.

(Click here for the blog article on muffler production)


Step

Mid-Forward Control Kit – Chrome – SR400/500

◯ Compared to the standard forward, this step kit provides about 120mm forward and 20mm down, providing a comfortable position. Even for tall people, your knees won’t bend too much and it won’t be cramped, so you can ride comfortably and firmly without getting tired.


Seat

BATES Type Genuine Leather Solo/Pillion Set Vertical Tuck Roll

〇A seat set with good cushioning made of genuine leather. The spring input position and angle settings, as well as the pillion pad mounting position, are set up in a fatigue-resistant configuration unique to 2%ER.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat/Pillion Pad Set

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

〇A mount kit that is easy to install on custom frames and the like. The lever ratio can also be changed, allowing for good cushioning.


Electrical Equipment

SR400/500 Custom Electrical Plate #2%er Original #SR400/500

〇All electrical components except the CDI are consolidated at the rear of the engine crankcase. It is easy to maintain as it can be accessed with both hands from either side of the vehicle, and there is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

IC blinker relay wide range specification

〇A wide-range turn signal relay that can be used without difficulty even with LED turn signals, supporting 1-150 watts. It can also be used as a repro for the original relay.

Battery Lesser

〇This is a battery-less kit that we manufacture in Japan.

Custom Ignition Switch Weld On Kit General Purpose

〇Easy to operate even while riding, welded and installed under the left side of the seat.


Kick Pedal

Brass Kick Pedal

◯Not only does it look good, but it also increases the pedal area, making it easier to kick. It’s a kit.


  • RearFenders, rear shocks, swingarms, etc.

    Hardtail

    “Rigid Line” Bolt-On Hardtail Kit』(13cm long, made to order)

    〇As the name suggests, this is a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to make it rigid. You can revert to the swing arm/rear shock specification when you go for vehicle inspection or when you want to change the style.


    Rear Wheel

    16″ Kit Steel Spoke SR400/500 Rear

    〇This is a kit that gives a powerful look, the same size as a typical Harley.

    Drilled plate torque rod SR400/500

    〇A drilled design torque rod to avoid interference with the wider tires.

    ‘FUCKSTONE 5.00-16 (Discontinued) (LOADSTAR TIRE 5.00-16)’

    〇A classic vintage style tire.


    Rear Fender/Sissy Bar

    ◯The rear fender is based on a typical flat fender, but it has been effectively reinforced on the back with suitable materials to withstand the slight vibrations of domestic vehicles and the weight and swing of the sissy bar for a long time. All parts involved in the installation are firmly mounted with high durability, intertwined with the reinforcement on the back.

    ◯The slightly slender fork line sissy bar is a one-off, made a little longer using hexagonal materials.


    Tail Lamp

    Bee High Tail Light Chrome

    ◯We have installed the standard tail at a good angle.


     

    Rear Blinker

    Diamond Winker Chrome 4pcs SET General Purpose

    Weld tab S size 4.5mm thick steel 2p

    〇Welded to the hardtail. Used as a blinker base.

    ※Parts Reference may show similar products or products with additional processing.