FrontHandlebars, F forks, headlights, etc.

【Front Fender】

“2%er Short Front Fender STD [SR400/500]“

〇A short fender that suits any style. Despite being made of FRP, it has a design with ribs around the perimeter like the original.

“SR400/500 Front fender upper stay“

〇A plate to lift and attach the fender when using tires with height (height).

---

【Front Wheel】

“Y`S Gear Cast Wheel”

---

【Front Tire】

【LOADSTAR TIRE 4.00-18】

◯ A classic watermelon pattern, high vintage style tire.

---

【Headlight】

“5.75 inch Bates Light Black Body/Chrome Rim”

“SR Bottom Mount Light Stay“

〇A classic headlight that matches well with the SR’s vehicle size and fork width. It is installed with a headlight stay that mounts low and close to the vehicle body.

---

【Handle/Handle Area】

◯ The separate handle that was attached at the time of delivery is used as is, and all controls are miniaturized to keep it neat.

“Amal type throttle holder, general purpose (for 7/8″)“

【Switch】

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇Easy to install mini turn signal switch with coupler on

(For different model years, it is installed with modifications on small headlights)

---

“Handle Lock Weld On Kit“

〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.

---

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle.

---

【Turn Signal】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style turn signal.

『SR400/500 Bottom Mount narrow blinker stay』

〇A stay to attach a 10mm turn signal to the bottom of the frame.

---

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.

CenterTank, oil tank, seat, step, muffler etc.

• The gasoline tank is a coffin tank design that follows the vintage style. We took a mold from the vintage model and resized it slightly smaller to fit the size of the SR frame, and made it from a single sheet of metal. The paint was done by “Kyoto P.H.K” in a different color but almost the same design as the “№120 SR400” that the owner admired.

---

【Muffler】

“Exhaust Pipe Flange Set for One-off Pipe Production”

〇We used a convenient production kit for the base of the mouthpiece. We produced a one-off semi-up muffler with a side exit, bending and connecting pipes in your preferred layout while consulting with you on the spot.

Ripple pipe for one-off muffler production, 45mm dia. 1-3/4

◯Used in the rear part of the muffler.

---

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring. (Powder coat finish)

---

【Seat】

◯The seat is a custom-made bucket type that supports the upper body weight over a wide range. The way the urethane is stacked and the design significantly reduce the strain on the arms and back due to weight transfer during acceleration. The tandem seat can be easily removed at any time with just one tool.

---

【Carburetor】

“FCR carburetor 39φ SR400/500 single unit“

〇Easy to start and handle, this carburetor recommended by 2%ER increases power by about two rounds in all ranges.

“Net funnel set for FCR carburetor“

〇This is a set of an aluminum funnel, upgraded from a red plastic one, and a stainless steel trash prevention net.

“Manifold Kit for FCR39φ”

〇This is a dedicated adapter to firmly fix the FCR carburetor to the SR400/500.

---

【Electrical Equipment】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500“

〇All electrical components except for the CDI are consolidated at the rear of the engine crankcase. It is easily accessible from either side of the vehicle, has good maintainability, and there is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without any problem with LED turn signals. It supports 1 to 150 watts and can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

---

【Kick Pedal】

“WR Replica Kick Pedal”

---

【Other Center/Body Surrounding Use Parts】
○ “Welding Tabs/Nuts” used for mounting gas tank tabs and seats
○ “Welding nut non-through M8 10p” used for gas tank and saddle seat spring receivers

RearFenders, rear shocks, swingarms, etc.

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made to order)

〇As the name suggests, this is a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to make it rigid line. You can revert it back to swing arm/rear shock specification during vehicle inspection or when changing styles.

---

【Rear Wheel】

◯Like the front, it has been replaced with “Y`S Gear Cast Wheel”.

---

【Rear Tire】

“Roadster 4.50-18 Tire”

〇The rear wheel is a standard 18-inch, with a vintage style, watermelon pattern classical tire selected.

“Drilled plate torque rod SR400/500“

〇It is a drilled design torque rod to avoid interference with the wider tire.

---

【Rear Fender】

◯The rear fender is a bob fender specified by the owner. We resized a fat bob for Harley, and to withstand the vibration of the SR and the load of two riders, we added effective reinforcement to the back and installed it safely.

---

【Tail Lamp】

◯The tail lamp was installed deeper using Lucas.

---

【Turn Signal】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style turn signal.

『Weld tab S size 4.5mm thick steel 2p』

〇Welded onto a hardtail. Used as a base for the turn signal.