FrontHandlebars, F forks, headlights, etc.

【Front Fork】

“2%er 10cm long Joints for Front Fork (pair) [SR400/500]“

〇High-quality stainless steel fork joint.

“Fork boots, general-purpose“

〇Classical universal fork boots.

---

【Front Wheel】

“2%er Front Wheel Aluminum Hub Cap [SR400/500]“

〇You can change to a classical style by sticking it on a normal drum brake.

---

【Front Fender】

“Front Iron Fender“

◯We mount the classical press-formed fender with a vintage design fender brace.

---

【Front Tire】

“Pirelli MT53 Replica 4.00-18”

〇A replica of the 70s Pirelli. It suits all styles, from street to tracker, scrambler, bobber, chopper, and more.

---

【Headlight】

“Old Bates Type Side Mount Light Kit SR400/500 XS650“

◯2%ER reproduces the custom parts from the 70s. The style remains the same as it was back then, but it uses a bright H4 bulb.

---

【Handle/Handle Area】

◯Deadstock pullback handle.

“Harley Type Replica Riser 6.5inch SR400/500“

◯We have manufactured a bolt-on riser of the Harley genuine type for SR.

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1200mm ’88~’08“

“[Special long brake wire for SR drum brake] 400mm“

“Clutch Wire 200mm Long“

〇We are using each long cable for the simple throttle.

---

“Chrome British Car Type Clutch Lever“

“Chrome British Car Type Brake Lever“

◯The controls are simplified with mini switches and the like.

---

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

---

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic chopper style blinker.

“Stem Mount Blinker Stay B Type”

〇A small quality stainless stay to mount a 10mm blinker on the stem side.

---

【Speedometer】

『Mechanical Speedometer 60mm Black Panel 1:4』

『Universal Speedometer Stay』

〇Mounted on the left front side of the gasoline tank, which is inconspicuous and highly visible.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“One-off Pipe Manufacturing Exhaust Pipe Flange Set”

“Universal Round Megaphone Muffler“

〇A one-off made using a convenient manufacturing kit for the mouthpiece at the root. A round megaphone silencer is attached.

---

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.

---

【Seat】

“Old School Double Seat II SR400/500“

○ It’s a standard seat for 2%ER’s normal frame custom, with features like button-down that’s hard to express in mass-produced items, and a design that looks stylish despite the thick urethane.

---

【Electrical Equipment】

◯ Under the seat is an “Oil Tank Type Electrical Case” (discontinued). We launched it because there were no parts of this kind that would suit a chopper.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without any problems with LED turn signals, supporting 1-150 watts. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we are manufacturing in Japan.

---

【Gasoline Tank Installation】

◯ Vintage coffin tank. The interior has been repaired and a tunnel has been created for SR use. It was safely mounted with a three-point rubber mount.

“Welding nut non-through M8 2p“

〇 A hole is drilled in the gasoline tank body and the nut is inserted and welded. It is non-penetrating, so it does not leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 The hole diameter is enlarged and changed to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. Here too, the hole diameter is enlarged and used with a rubber mount.

---

【Carburetor】

◯525cc Engine × CR 38φ Black Body.

---

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

---

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Sissy Bar】

“SR400/500 Sissy Bar Plate Hole Type Single Unit“

〇Old school design with perforated side plates. We used only the side plates and custom-made the bar part.

---

【Rear Fender】

“Rear Iron Fender“

◯ Launched as a replica of the Shovel Sportster era rear fender.

---

【Rear Tire】

“Pirelli MT53 Replica 4.00-18”

〇A replica of the 70s Pirelli. It suits all styles, from street to tracker, scrambler, bobber, chopper, and more.

---

【Rear Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A blinker in the chopper style.

---

【Drive System】

“Rear sprocket SR400/500 428-56“

● A durable sprocket made of steel.

“O-ring chain 428-130L“

● A replacement drive chain with built-in O-rings.