FrontHandlebars, F forks, headlights, etc.

【Front Fork】

“Fork boots, general-purpose“

〇Classic universal fork boots.

【Front Tire】

“LOADSTAR TIRE 4.50-18“

〇We select one size larger than usual. The handle will be heavier, but it has volume and emphasizes the vintage feel.

【Headlight】

◯ The headlight is a vintage Unity brought in by the customer.

For replica products, see here↓

“Unity Replica Headlight“

【Handle/Handle Area】

◯Owner-made handle.

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1000mm ’88~’08“

“Brake Wire 100mm Long“

“Clutch Wire 100mm Long“

〇Using long cables for a simple throttle.

“Chrome British Car Type Clutch Lever“

“Chrome British Car Type Brake Lever“

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style blinker.

『SR400/500 Bottom Mount narrow blinker stay』

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

CenterTank, oil tank, seat, step, muffler etc.

【Seat】

◯The seat was found in 2%ER. It is reinforced with an aluminum back plate and mounted on springs.

“Welding nut non-through M8 2p“

〇Used on the frame side as a seat spring receiver.

【Electrical】

◯ The bundled electrical and harness components under the seat rail are concealed by roughly hammering out an aluminum plate to match the atmosphere of the vehicle body.

“Custom Ignition Switch Weld On Kit General Purpose“

〇 Welded and installed on the lower left of the seat for easy operation even while riding.

【Gas Tank Installation】

◯ The gas tank is a Yamaha small-displacement model brought in by the owner, which has been modified and reused. The inside, which was in a shabby condition, has been repaired with sheet metal repair, rust removal / coating. The tunnel has been modified and firmly mounted with three-point rubber.

“Welding nut non-through M8 2p“

〇Drill a hole in the gas tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇The hole diameter is enlarged and changed to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with rubber mounting.

【Engine Area】

“Breather filter SR400/500“

〇A filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Tire】

“LOADSTAR TIRE 4.50-18“

〇A staple of vintage style, the watermelon pattern.

【Tail Lamp】

◯The owner brought in a homemade fender brace and had the tail lamp mounted. The drilled iron plate is intentionally left unpainted.

【Number Plate】

〇 Using only the stay part of the “Side Number Kit”, the number was side-mounted.

【Rear Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style blinker.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.