FrontHandlebars, F forks, headlights, etc.

●The front fork has been extended to a moderate length, and

with the selection of small, rounded front tires, the typically heavy handling is set to a weight level that allows for normal city riding.

With the conversion to a jockey shift, the clutch lever has been eliminated, resulting in an extremely simple handlebar area.

---

【Front Fork Area】

“100mm Fork Joint”¥17,800

〇High-quality stainless steel fork extension kit

“Front Fork Dust Seal”¥2,400

〇A very simple dust seal. It can also be used as a replacement for the original fork boots that become unusable when the fork is lengthened.

---

【Front Wheel】

“SHINKO flute 3.00-18”¥12,800

〇A street tire with a vertical groove design. It helps to lighten the handling that tends to become heavy when long forks are used. It is a small, rounded 3.00 size.

---

【Handle/Surroundings】

“Riserless Narrow Pullback Handle” ¥27,000

〇Chopper handle of the direct attachment type to the top bridge.

“Amal type throttle holder, general purpose (for 7/8″)” ¥4,180

 “Amal type slot wire 1000mm ’88~’08” ¥2,750

“600mm Long Brake Cable”¥4,800

“Sharp End Lever Assy for Harley”

〇We are installing a processed lever for Harley, a vintage replica.

---

【Switch】

“Mini Turn Signal Switch Coupler On Kit (’85~00)”¥3,950

〇Easy to install mini turn signal switch with coupler on

---

“Handle Lock Weld On Kit” ¥4,200

〇We have newly installed a handle lock under the stem, which is inconspicuous and easy to operate.

“MOTOR ROCK Decompression lever” ¥4,500

〇A decompression lever directly attached to the engine to simplify the area around the handle.

---

【Headlight】

“5.75 inch Bates Light HS Type Chrome”¥10,500

〇This is a Bates light for custom vehicles with a harness storage type that can store many harnesses and couplers inside the light.

“Bottom Mount Light Stay II” ¥2,400

〇A headlight stay that suits the chopper style well with its moderate height and protrusion. (5.75 inch Bates Light Set II SR400/SR500)

---

【Front Blinker】

“Certified Star Beans Blinker/Black 2p”¥7,250

〇World’s smallest size, certified with E-mark, inspection OK ultra-small blinker

“Universal Blinker Stay 10A Type Steel”¥2,200

〇Installation of ultra-small micro blinker on the front side of the lower engine mount.

---

【Speedometer】

【Small Tank Left Side Meter Kit】¥14,900

〇When replacing with a small tank such as a sports tank, this is a kit that allows you to bolt on a 60φ meter in a place that is easy to see and not noticeable.

『Extension meter cable joint』¥1,900

〇Used when extending the fork or relocating the meter.

CenterTank, oil tank, seat, step, muffler etc.

●The Narrow Sports Star Tank is safely mounted with three rubber points.

The frame under the seat is cut from the original part, and rebuilt with thick steel pipes considering strength, precision, durability, and maintainability, according to the angle of the “Hardtail Kit“.

The muffler has been drastically changed by the specified one-off and conversion to the FCR carburetor.

---

【Muffler】

“One-off Muffler”

〇It’s a full exhaust muffler.

---

【Step/Shift】

“Mid-High Jockey Shift Kit Chrome for SR400/500” ¥92,500

〇Maintaining the comfortable riding posture of the mid-high step, this is a jockey shift kit that focuses on operation feel such as touch and stroke.

The pegs and step rubber on this vehicle have been changed to white.

---

【Gasoline Tank Installation】

“Narrow Sportster Tank for Production” (Coming Soon)

“Welding nut non-through M8 2p” ¥1,700

〇Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p” ¥930

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p” ¥1,250

〇Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.

---

【Seat】

“Narrow Type Bates Replica Solo Seat, Flat Base, White” ¥16,000

〇A seat with a good atmosphere, even though it’s vinyl leather.

“2 Inch Spring Comfort Mount Set for Narrow Bates Replica Solo Seat” ¥17,000

〇A mount kit that is easy to install on custom frames and the like. The lever ratio can also be changed, allowing for good cushioning.

---

【Carburetor】

“FCR carburetor 39φ SR400/500 single unit” ¥71,000

〇2%ER recommended, your slow SR will be dramatically transformed. It’s a carburetor that’s easy to handle with sharp and smooth acceleration.

“Net funnel set for FCR carburetor” ¥10,900

〇Change from a plastic red funnel to aluminum, it’s a set with a stainless steel trash prevention net.

“Manifold Kit for FCR39φ” ¥12,000

〇It’s a dedicated adapter to firmly fix the FCR carburetor to the SR400/500.

---

【Electrical Equipment】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500” ¥4,200

〇All electrical components except the CDI are consolidated at the rear of the engine crankcase. It is easy to maintain as it can be accessed with both hands from either side of the vehicle, and there is no need to reassemble even when returning to swing arm specifications for vehicle inspection.

 “IC blinker relay wide range specification” ¥2,400

〇A wide-range turn signal relay that can be used without difficulty even with LED turn signals. It can also be used as a repro for the original relay.

“Battery Lesser” ¥3,400

〇This is a battery-less kit made in Japan.

“BT Type Custom Ignition Switch Bolt-On Kit” ¥6,500

〇A custom main key that can be used even on vehicles equipped with a battery.

 “ETC”

〇Installed additionally as per the owner’s request.

 “Battery Tray & Battery for Hardtail”

〇The battery is installed in a way that it is not easily noticeable. (Minor modifications around the area are necessary)

---

【Engine Area】

“Breather filter SR400/500” ¥3,500

〇This is a filter kit required when removing the original air cleaner.

---

【Drive System】

“Front sprocket SR400/500 428-19” ¥2,000

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

●The combination of a hardtail kit (13cm long) that determines the overall styling, a sturdy steel rib fender,

and a simple, one-off stainless steel sissy bar.

---

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made-to-order) ¥78,000

〇As the name suggests, it’s a hardtail kit that can be attached and detached with bolts/nuts. It remodels the seat rail of the original frame into a rigid line.

You can revert to the swing arm/rear shock specification when you have a vehicle inspection or when you want to change the style.

---

【Rear Fender】

“5-Inch Custom Rib Fender – Steel Material” ¥15,070

“Reinforcement Back Plate for 5-Inch Rib Fender” ¥2,200

〇A thick and durable rib fender. A reinforcement plate is added around the mounting holes for even more robust mounting.

“Weld Tab M Size 3mm Stainless” ¥1,500

〇Used as a mounting stay for fender x fender brace

---

【Rear Tire】

『16″ Kit Steel Spoke SR400/500 Rear』¥28,000

〇This is a kit that gives a powerful look with the same size as a typical Harley.

『LOADSTAR TIRE　5.00-16』¥16,500

〇A classic vintage style tire

『Drilled plate torque rod SR400/500』¥6,300

〇A drilled design torque rod to avoid interference with the wider tire.

---

【Tail Lamp】

69 tail type3¥10,000

◯The sissy bar is made of stainless steel.

---

【Rear Blinker】

“Certified Star Beans Blinker/Black 2p”¥7,250

〇World’s smallest size E-mark certified, inspection OK ultra-small blinker

“Weld Tab A Type for Blinker Stay”¥2,000

〇Welding stay for up to 6mm mounting blinker.

---

【Drive System】

“Rear sprocket SR400/500 428-56 ” ¥4,800

〇An affordable and durable replacement sprocket