#253 SR400

Custom Bike

#253 SR400Custom Report

The owner is a female model who is active under the name “Renhi Queen”. This SR400 was ordered as her everyday chopper, which she uses in custom shows and magazines. Contrary to the glamorous image of “Renhi Queen” that many people have, this vehicle is designed in an aged old school chopper style so that she can ride it without any worries in her daily life.

Based on the “STD Hardtail Complete“, the rear uses a 13cm long bolt-on hardtail kit, and the styling is designed to be able to accommodate further long fork modifications in the future. It is finished in a slightly rough silhouette that does not become too smart overall.

Of course, not only the styling, but also the maintenance and ride comfort of this vehicle have been carefully crafted.

The handle is a prototype tiller bar designed with mass production in mind. The high back seat is designed to hold the entire upper body weight by determining the position of the internal backrest frame while the owner is actually straddling it, significantly reducing fatigue in the arms and shoulders due to acceleration G. The design makes it hard to feel the rigid push-up that would normally make your buttocks and waist painful because the area increases and the weight is dispersed. The step adopted is the genuine forward step that comes in a position to distribute the lower body weight effectively according to the owner’s physique.

The gas tank and fender paint, which is based on the race and has a gradation of shades and a bit of aging added, was requested from “BACON“.


【Detailed Introduction Video】

Cookie consent is required to display this video.


IG “Renhi (@queen_bigben)


The sample car based on the STD Hardtail Complete is here

Over 70 examples of Hardtail production are here


8/21 Planned vehicles for exhibition at Kobe New Order Chopper Show

 

Custom List

FrontHandlebars, F forks, headlights, etc.

●With further long fork modifications in mind, we have created the front area with a 3.00-18 small diameter tire and some long fork modifications. The tiller bar handle, which was designed with mass production in mind, is designed to be easily handled even by girls with less strength.


Front Fork

2%er 15cm long Joints for Front Fork (pair) [SR400/500]

〇High-quality stainless steel fork joint.

Fork boots, general-purpose

〇Classic universal fork boots


Headlight

5.75 inch Old Bates Type Side Mount Headlight #5.75 inch headlight #General-purpose parts

〇Vintage style side mount headlight. H4

Old Bates Type Side Mount Light Stay SR400/500, XS650 #5.75 inch headlight #2%er Original #SR400/500 #XS650

〇Headlight stay molded from vintage


Handle, Around the Handle

Amal type throttle holder, general purpose (for 7/8″)

Amal type slot wire 1100mm ’88~’08

300mm Long Brake Cable

200mm Long Clutch Cable

Barrel Grip Black 22.2mm 7/8inch for Motorcycle

〇The handle is a one-off tiller bar developed with future commercialization in mind.


Aluminum Short Brake Lever/Holder Set

Aluminum Short Clutch Lever/Holder Set

〇This is a compact and easy-to-grip aluminum lever set.


Switch

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇A mini turn signal switch that is easy to install with a coupler on

(It is installed with modifications for different model years and small headlights)


Handle Lock Weld On Kit

〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate


MOTOR ROCK Decompression lever

A decompression lever directly attached to the engine to simplify the area around the handle


Speedometer

Mechanical Speedometer 60mm Black Panel 1:4

Universal Speedometer Stay

〇Mounted on the left front side of the gasoline tank, which is not easily noticeable and has high visibility

Extension meter cable joint

〇Extension cable for the meter installed in a place where the length is insufficient


Turn Signal

Small Bullet Turn Signal Chrome 4pcs SET General Purpose

〇A classic among classics. A chopper-style turn signal.

SR400/500 Bottom Mount narrow blinker stay

〇A stay to attach a 10mm turn signal to the bottom of the frame.


CenterTank, oil tank, seat, step, muffler etc.

●The Sports Star Tank is securely mounted with three rubber points. The frame under the seat is rebuilt to match the angle of the rear “Hardtail Kit“, considering strength, precision, durability, and maintainability, by cutting the original part and using thick steel pipes.


Muffler

Torque cone drag pipe muffler SR400/500

〇This is a full exhaust muffler with a torque cone that we developed in-house built into the mouthpiece


Gasoline Tank Installation

“Sportster Tank”

Welding nut non-through M8 2p

〇Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

Weld tab M size 4.5mm thickness 2p

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

Weld tab L size 4.5mm thick steel 2p

〇Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.


Seat

“High Back Seat” (One-off)

〇This is a seat that is extremely easy to ride due to the backrest frame tailored to the owner’s body shape embedded inside.


Electrical Equipment

SR400/500 Custom Electrical Plate #2%er Original #SR400/500

〇All electrical components except the CDI are consolidated at the rear of the engine crankcase. It is easily accessible from either side of the vehicle and has good maintainability. There is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

IC blinker relay wide range specification

〇A wide-range turn signal relay that can be used without any problem even with LED turn signals. It supports 1 to 150 watts and can also be used as a replacement for the original relay.

“Battery Tray Kit for Hardtail” (Prototype, decided to be commercialized)

〇A tray kit for mounting a battery, which has been increasingly requested. It is also equipment for installing ETC after delivery.


Engine Area

Breather filter SR400/500

〇This is a filter kit needed when removing the original air cleaner


Drive System

Front sprocket SR400/500 428-19

〇A durable replacement sprocket made of steel.


  • RearFenders, rear shocks, swingarms, etc.

    ●Finished with a 13cm long hardtail kit, 16-inch wheels, a flat fender reinforced on the back, old-school tail lights, and a one-off custom sissy bar.


    Hardtail

    “Rigid Line” Bolt-On Hardtail Kit』(13cm long, made to order)

    〇As the name suggests, it’s a hardtail kit that can be attached and detached with bolts/nuts. It remodels the seat rail of the original frame to make it a rigid line. You can revert to a swing arm/rear shock specification when you need to pass an inspection or change the style.


    Turn Signal

    Small Bullet Turn Signal Chrome 4pcs SET General Purpose

    〇A classic among classics. A chopper-style turn signal.

    Weld tab S size 4.5mm thick steel 2p

    〇Welded onto a hardtail. Used as a base for the turn signal.


    Fender, Sissy Bar

    “Flat Fender, Square Bar Sissy Bar” (One-off)

    〇A sissy bar deliberately finished with a rough silhouette. The flat fender is safely mounted at six points

    “Lucas Tail Lamp Number Base Set”

    〇Easy-to-install Lucas tail with a base plate included


    Drive System

    Rear sprocket SR400/500 428-56

    〇An affordable and durable replacement sprocket

    ※Parts Reference may show similar products or products with additional processing.