FrontHandlebars, F forks, headlights, etc.

【Front Fork】

“Fork boots, general-purpose“

〇Classic universal fork boots.

【Front Fender】

“CHUCK BOX Front short fender Stainless steel for SR400/SR500“

◯A front fender made entirely of stainless steel. It is a carefully crafted handmade piece made in a chuck box.

“SR400/500 Front fender upper stay“

〇A plate to lift and attach the fender when using tires with height (height).

【Front Tire】

『LOADSTAR TIRE 4.00-18』

〇A classic watermelon pattern, high vintage style tire.

【Handle】

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 800mm ’88~’08“

“Brake wire/100mm 200mm 300mm 600mm SR400/500 #SR400/500“

“Clutch wire/300mm 200mm 100mm standard SR400/500 ALL YEARS“

〇We are using each cable with a simple throttle.

【Front Blinker】

“Small Bullet Turn Signal Matte Black 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the frame bottom.

【Speedometer】

“Smith style speedometer 80mm 1:4“

◯The meter is simply a single meter specification.

CenterTank, oil tank, seat, step, muffler etc.

【Seat】

“General Purpose Rib Sheet Cowl FRP 2%er Original“

◯The seat is one-off. It acts as a stopper for the upper body weight. By holding it around the top of the tailbone, you can ride more comfortably than you might imagine.

【Electrical Equipment】

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can easily be used with LED turn signals and supports 1-150 watts. It can also be used as a replacement for the original relay.

【Gas Tank Installation】

“Triumph tank (fabrication material)“

◯The gas tank is modified and installed for Triumph and Bonneville.

“Welding nut non-through M8 2p“

〇Drill a hole in the body of the gas tank, insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter, change to rubber mount specification, and hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Tire】

“LOADSTAR TIRE 4.50-18“

〇A classic vintage style watermelon pattern. It’s a rear tire with height and volume.

【Rear Shock】

◯The covered type rear shock is made by Daytona. It will be lowered by 2 cm.

Similar products are here↓

“Half Cover for Classical Rear Shock SR400/500“

【Rear Subframe】

“Loop Frame for SR400/500 and Others“

〇This is a steel pipe for processing the rear loop frame.

【Rear Turn Signal】

Small Bullet Turn Signal Matte Black 4pcs SET General Purpose

〇A classic among classics. A chopper-style turn signal.

“Rear Bottom Mount Turn Signal Stay”

〇A stay to attach the turn signal to the swing arm.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.