#126 SR400Custom Report
One of the complete custom models of 2%ER, the SR400, was ordered as an “STD Hardtail“.
The exterior and muffler are almost the same as the sample complete car, and it’s a standard bobber/chopper style, but with a slightly higher one-off handlebar to match the large owner, it has a position that fits the physique.
With a beautiful frame that incorporates a “rigid line” bolt-on hardtail by removing the swing arm and rear shock, the rear section can be attached and detached with bolts/nuts, as the name “bolt-on” suggests. You can pass the vehicle inspection with peace of mind by reassembling it on the swing arm.
“Click here for the article published in THE SR TIMES ”
“Click here for the blog post about the completion and delivery”
“Movie of the right side of the car body”

“Movie of the left side of the car body”

“Movie of a light test drive after passing the vehicle inspection two years later”

Custom List
FrontHandlebars, F forks, headlights, etc.
【Front Tire】
◯ A classic watermelon pattern, a vintage style tire with height.
【Headlight】
“5.75 inch Bates Light Chrome General Purpose“
〇A headlight that fits well with the SR’s vehicle size and fork width, and can be installed without any discomfort.
〇A headlight stay that fits well with the chopper style due to its moderate height and protrusion. (5.75 inch Bates Light Set II SR400/SR500)
【Handle/Handle Area】
◯A one-off piece that was positioned with the owner straddling it.
“Amal type throttle holder, general purpose (for 7/8″)“
◯The handle area, controls, meter, ignition-related parts are all neatly processed in the 2%ER standard style.
【Switch】
“Mini Turn Signal Switch Coupler On Kit (’85~00)”
〇Easy to install mini turn signal switch with coupler on
〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.
“MOTOR ROCK Decompression lever“
A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)
【Front Blinker】
“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
“SR400/500 Bottom Mount narrow blinker stay“
〇A stay to attach a 10mm blinker to the bottom of the frame.
【Speedometer】
“Mechanical Speedometer 60mm Black Panel 1:4“
〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.
CenterTank, oil tank, seat, step, muffler etc.
【Muffler】
〇Easy installation with slip-on to the original exhaust pipe. It’s an up-muffler typical of a chopper.
【Seat】
◯ Selected a solo saddle seat with springs, just like the complete sample.
(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat Black
“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”
〇 A mount kit that is easy to attach mainly to custom frames. You can also change the lever ratio and create a good cushioning effect.
【Electrical Equipment】
“IC blinker relay wide range specification“
〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.
〇This is a battery-less kit made entirely in Japan.
“Custom Ignition Switch Weld On Kit General Purpose“
〇Easy to operate even while riding, it is welded and installed under the left side of the seat.
【Gasoline Tank Installation】
“Narrow Sportster Tank for Production”
“Welding nut non-through M8 2p“
〇Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.
“Weld tab M size 4.5mm thickness 2p“
〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.
“Weld tab L size 4.5mm thick steel 2p“
〇Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.
【Engine Area】
〇This is a filter kit needed when removing the original air cleaner.
【Drive System】
“Front sprocket SR400/500 428-19“
〇A durable replacement sprocket made of steel.
RearFenders, rear shocks, swingarms, etc.
【Hardtail】
『Rigid Line Bolt-On Hardtail Kit SR400/500』(5cm Long)
〇As the name suggests, it’s a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to a rigid line. You can revert to a swing arm/rear shock specification during vehicle inspection or when changing styles.
【Rear Wheel】
“Drilled plate torque rod SR400/500“
〇A torque rod with a drilled design to avoid interference with wider tires.
〇A classic vintage style watermelon pattern. It’s a rear tire with height and volume.
【Rear Blinker】
“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
“Weld tab S size 4.5mm thick steel 2p“
〇Welded onto a hardtail. Used as a blinker base.
【Drive System】
“Rear sprocket SR400/500 428-56“
〇An affordable and durable replacement sprocket.
※Parts Reference may show similar products or products with additional processing.