#12 SR400

Custom Bike

#12 SR400Custom Report

Recreated on the streets of Japan, inspired by the 80’s drag racers. Each part is polished, chrome-plated, and candy-painted from the frame to evoke the atmosphere of the time. H-type rims of normal width so as not to become thick. The gas tank is a modified and reused XS650, and the Cal look paint was requested from Kamikaze Pinstripe. The seat cowl is made by GOODS, and its shape has been modified for use.

 


〇 “SR TIMES” WEB Magazine Article is Here

〇 “E-PUB.JP” Published Article is Here

〇 “CHOPPER JOURNAL” Published Article is Here


 

Custom List

FrontHandlebars, F forks, headlights, etc.

Front Fork

◯3cm lowered. The bottom case is finished with smoothing & polishing.


Front Wheel

H-shape aluminum rim SR front standard size

〇The H-type rim on the old disc hub will upgrade your vehicle. The disc cover plate is on the classic disc rotor made by Sunstar. The caliper for ’01 and up is polished. The brake master is using the original Estrella, polished.

“SHINKO flute 3.00-18”

〇A street tire with a vertical groove design. It corrects the heavy handling that tends to occur when the fork is lengthened. It is a small, rounded 3.00 size.

“Front Disc Rotor TRAD type1 `01~”

〇A classical design disc rotor made by Sunstar, old model type.


Headlight

“Sportster Type Headlight”

〇A bright H4 bulb headlight with a visor. It is installed by relocating the main key.


Handle, Around the Handle

Ace Bar Type1

◯ It’s extremely simple, but the angle of droop and the length of the bar make it the perfect handle for a traditional cafe racer style.

“Top Bridge for Separate Handle”

〇 A classic style top bridge without holes for the bar handle, used with smoothed stays.

Amal type throttle holder, general purpose (for 7/8″)

Amal type slot wire 900mm ’88~’08

Brake wire/100mm 200mm 300mm 600mm SR400/500 #SR400/500

Clutch wire/300mm 200mm 100mm standard SR400/500 ALL YEARS

〇 We are using each cable with a simple throttle.


MOTOR ROCK Decompression lever

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)


Front Blinker

Diamond Winker Chrome 4pcs SET General Purpose


Speedometer

Mechanical Speedometer 60mm Black Panel 1:4

Universal Speedometer Stay

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.


CenterTank, oil tank, seat, step, muffler etc.

Seat

◯One-off seat. The seat cowl is made by GOODS, and its shape has been modified for use.


Gasoline Tank Installation

◯ The tank is a modified XS650. The Cal look paint was done by Kamikaze Pinstripe.

Welding nut non-through M8 2p

〇Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

Weld tab M size 4.5mm thickness 2p

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

Weld tab L size 4.5mm thick steel 2p

〇Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.


Electrical Equipment

Brat Style Electrical Plate

〇A simple electrical plate that makes it easy to organize harnesses and electrical components.

IC blinker relay wide range specification

〇A wide-range turn signal relay that can handle 1-150 watts and can be used without difficulty even with LED turn signals. It can also be used as a replacement for the original relay.

Battery Lesser

〇A battery-less kit made in Japan.

Custom Ignition Switch Weld On Kit General Purpose

〇Easy to operate even while riding, welded on the lower left of the seat.


Engine Area

Breather filter SR400/500

〇This is a filter kit needed when removing the original air cleaner.


Drive System

Front sprocket SR400/500 428-19

〇A durable replacement sprocket made of steel.


  • RearFenders, rear shocks, swingarms, etc.

    Rear Wheel

    H Aluminum Rim SR Rear Standard Size

    ◯ The wheel hub and brake panel are polished and equipped with an H-type aluminum rim.


    Rear Shock

    ◯Billet suspension with a 7cm long swing arm.


    Rear Blinker

    Diamond Winker Chrome 4pcs SET General Purpose


    Drive System

    Rear sprocket SR400/500 428-56

    〇A durable sprocket made of steel.

    ※Parts Reference may show similar products or products with additional processing.