#112 SR400Custom Report
It was created as a cool chopper style that doesn’t extend the fork, as seen in Triumphs from the 60s.
The bulky gas tank, handlebars with a gentle curve, and the rough style of the swing arm with a sissy bar allow you to ride casually without choosing your fashion,
You can easily ride from city patrols to long tours.
It’s a recommended style for 2%ER as a chopper style that’s not intimidating.

Custom List
FrontHandlebars, F forks, headlights, etc.
【Front Fork】
〇Classic universal fork boots.
【Headlight】
“Old Bates Type Side Mount Light Kit SR400/500 XS650“
◯A headlight molded from a vintage Bates from the 60s.
【Handle/Handle Area】
◯An up-handle designed to suit all styles, from normal frames to hardtails.
“PAUGHCO type 3inch Square Riser SR400/500“
〇A handle post of a very usable height that retains the atmosphere of the time. It lifts the atmosphere and position.
“Amal type throttle holder, general purpose (for 7/8″)“
“Amal type slot wire 1200mm ’88~’08“
◯Controls are kept simple with mini switches and the like.
【Switch】
“Mini Turn Signal Switch Coupler On Kit (’85~00)”
〇Easy to install mini turn signal switch with coupler on
【Front Tire】
“Pirelli MT53 Replica 4.00-18”
〇A replica of the 70s Pirelli. It suits all styles, from street to tracker, scrambler, bobber, chopper, and more.
“MOTOR ROCK Decompression lever“
A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)
【Front Blinker】
『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』
〇A classic among classics. A chopper-style blinker.
【Speedometer】
“Smith style speedometer 80mm 1:4“
◯ We installed a large meter as the center meter in the style of a British car.
CenterTank, oil tank, seat, step, muffler etc.
【Muffler】
『Slip-On Megaphone Muffler for SR400/500』
〇A reverse cone muffler that is slip-on mounted on a normal exhaust pipe. It has one of the deepest bass sounds among the many aftermarket mufflers.
【Step】
“Mid-High Control Parkerized for SR400/500“
〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.
【Seat】
“Old School Double Seat II SR400/500“
〇It’s a standard seat for 2%ER’s normal frame custom, with features that are difficult to express in mass-produced products, such as button-down, thick urethane that still looks stylish.
【Electrical Equipment】
“Genuine ignition switch relocation stay (`03~ with immobilizer) SR400“
◯ Relocate the standard main key to the less noticeable front left of the gas tank with a bolt-on.
“IC blinker relay wide range specification“
〇 A wide-range turn signal relay that can handle 1-150 watts and can be used without difficulty even with LED turn signals. It can also be used as a replacement for the standard relay.
〇 A battery-less kit made in Japan.
【Gas Tank Installation】
“Triumph tank (fabrication material)“
◯The gas tank is a one-off Triumph type. It was made 2 cm narrower than the usual one. The simple aging paint that never gets old was requested from “BACON“.
“Welding nut non-through M8 2p“
〇Drill a hole in the gas tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.
“Weld tab M size 4.5mm thickness 2p“
〇The hole diameter is enlarged and changed to a rubber mount specification to hold the non-penetrating nut. Used on both sides.
“Weld tab L size 4.5mm thick steel 2p“
〇Used for the rear installation of the gas tank. This one also has an enlarged hole diameter and is used with a rubber mount.
【Engine Area】
〇A filter kit needed when removing the original air cleaner.
【Drive System】
“Front sprocket SR400/500 428-19“
〇A durable replacement sprocket made of steel.
RearFenders, rear shocks, swingarms, etc.
• The rear area is equipped with a sissy bar on the swing arm. To avoid making it look like a street vendor’s bike, we focused on balance and installation methods from the 1960s, and made it simple with an emphasis on atmosphere.
【Rear Shock】
〇A rear shock that lowers by about 4cm. It moves well among low-down suspensions. (Removal of the original chain case is necessary)
【Rear Subframe】
“Loop Frame for SR400/500 and Others“
〇It is a steel pipe for processing the rear loop frame.
【Sissy Bar】
◯ A hexagonal sissy bar, made entirely in the style of the time, for the “loop frame” end.
【Rear Fender】
“5-Inch Custom Rib Fender – Steel Material“
“Reinforcement Back Plate for 5-Inch Rib Fender“
〇A thick and durable rib fender. A reinforcement plate is added around the mounting hole to mount it even more robustly. Finished in plating.
【Rear Tire】
“Pirelli MT53 Replica 4.00-18”
〇A replica of the 70s Pirelli. It suits all styles, from street to tracker, scrambler, bobber, chopper, and more.
【Tail Lamp】
『Lucas tail lamp with pedestal Japanese standard number size』
◯This is a tail lamp that is easy to use with a Japanese standard number size, while having the atmosphere of a good imported body.
【Rear Blinker】
『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』
〇A classic among classics. A chopper-style blinker.
【Drive System】
“Rear sprocket SR400/500 428-56“
〇An affordable and durable replacement sprocket.
〇A replacement drive chain with built-in O-rings.
※Parts Reference may show similar products or products with additional processing.