FrontHandlebars, F forks, headlights, etc.

【Front Fork】

“2%er 10cm long Joints for Front Fork (pair) [SR400/500]“

◯Extend the front fork moderately. Smooth and polish the unnecessary stays on the bottom case.

---

【Front Wheel】

“SR400/500 21inch kit for front“

〇A wheel kit that results in a narrow, large-diameter, sharp style. The wheel hub is finished with sandblasting. The tire is AVON MKⅡ.

“2%er Front Wheel Aluminum Hub Cap [SR400/500]“

〇You can change to a classical style by attaching it to a normal drum brake.

---

【Headlight】

“Unity Replica Headlight“

◯ Mounted with a light stay made of stainless steel.

---

【Handle/Handle Area】

◯The deformed Z-bar handle is a one-off made of stainless steel. Of course, it is made to fit the owner’s physique.

“SR400/500 Handlepost Offset Collar“

◯The installation width is widened and balanced. The top bridge is smoothed, and it is polished together with the handle post.

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1100mm ’88~’08“

“Brake Wire 200mm Long“

“Clutch Wire 100mm Long“

〇We use long cables for the simple throttle.

---

“Chrome British Car Type Clutch Lever“

“Chrome British Car Type Brake Lever“

◯The controls are finished in a simple British style with mini switches and the like.

---

【Switch】

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇Easy to install mini turn signal switch with coupler on

---

“Handle Lock Weld On Kit“

〇We have newly installed a handle lock under the stem, which is inconspicuous and easy to operate.

---

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

---

【Front Blinker】

“Diamond Winker Chrome 4pcs SET General Purpose“

“Diamond Blinker Stay“

◯The blinker is attached to the bottom of the frame.

---

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

◯A one-off full exhaust that pays attention to the angle under the belly that determines the silhouette of the vehicle body.

---

【Step】

Mid-High Step Kit Chrome for SR400/500

〇This step kit is essential for 2%ER’s custom, which makes the riding posture cool and the position extremely less tiring.

---

【Seat】

◯A one-off solo seat. The comfort is incomparable to a suspension-equipped chopper that is built without considering the mounting angle, springs, and handlebar position according to the physique.

“Welding nut non-through M8 2p“

〇Used on the frame side as a seat spring receiver.

---

【Seat Rail】

◯The seat underframe is drop-processed. This is a standard method in SR Chopper, but it is processed more simply in 2%ER.

---

【Electrical Equipment】

◯Under the seat is a custom-made electrical equipment case. It is designed to open and close on the left side for easy maintenance.

“Battery Lesser“

〇This is a battery-less kit that is made entirely in Japan.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can handle 1-150 watts without any problem even with LED turn signals. It can also be used as a replacement for the original relay.

---

【Gasoline Tank Installation】

◯ The custom-made gas tank is a narrow egg type. It’s a tank that meets the owner’s desire for capacity, mounted with a one-off stainless steel stay. We made it with a design that won’t get boring. (Click here for a video of the custom tank production)

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body and insert it for welding. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This one also has an enlarged hole diameter and is used with a rubber mount.

---

【Engine Area】

◯The engine case is fully polished.

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

---

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇Change to the standard wheel size for choppers, the tire is a Coker whitewall. The wheel hub is finished with sandblasting, and the brake panel is finished with black paint.

---

【Rear Shock】

◯ In order to make it narrow, the rigid suspension part is carved out at the very clearance between the inside of the rigid suspension and the tire. It’s thin. The swing arm is extended by 6cm. This allows for a wider seat surface, which greatly improves comfort. The bike becomes larger and does not become unbalanced even when someone is riding it.

---

【Rear Fender】

“5-Inch Custom Rib Fender – Steel Material“

● A durable, universal rib fender with thickness.

“Reinforcement Back Plate for 5-Inch Rib Fender“

● We have added a reinforcement plate around the mounting holes and areas under stress to mount it even more robustly.

---

【Rear Blinker】

“Diamond Winker Chrome 4pcs SET General Purpose“

“Weld tab S size 4.5mm thick steel 2p“

〇Welded to the hardtail. Used as a blinker base.

---

【Drive System】

『Rear sprocket SR400/500 428-56 』

〇An affordable and durable replacement sprocket.