FrontHandlebars, F forks, headlights, etc.

【Front Tire】

【LOADSTAR TIRE 4.00-18】

◯A classic watermelon pattern, high vintage style tire.

【Headlight】

“5.75 inch Bates Light Black Body/Chrome Rim”

“Bottom Mount Light Stay II“

〇A headlight stay that suits the chopper style well with its moderate height and protrusion. (5.75 inch Bates Light Set II SR400/SR500)

【Handle/Handle Area】

“Short Z Bar Handle” (Discontinued)

“Flat Bar Replica Riser 2.5 Inch“

“Amal type throttle holder, general purpose (for 7/8″)“

“Handle Lock Weld On Kit“

● Attached to the less noticeable and easy-to-operate lower part of the stem.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle.

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

『Mechanical Speedometer 60mm Black Panel 1:4』

『Universal Speedometer Stay』

〇Mounted on the left front side of the gasoline tank, which is inconspicuous and has high visibility.

CenterTank, oil tank, seat, step, muffler etc.

【Step】

“Mid-Forward Control Kit – Chrome – SR400/500“

◯Even for tall owners, the vehicle does not look small when straddled, and you can ride comfortably with this forward control.

【Seat】

“BATES Type Genuine Leather Solo Saddle Seat Vertical Tuck Roll Black/White“

〇A genuine leather solo saddle seat with a balanced price, look, and comfort. It is installed with a soft ride that is less likely to bottom out by changing the mounting angle and spring input position.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat Black

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

〇A mount kit that is easy to install on custom frames and the like. The lever ratio can also be changed, allowing for good cushioning.

【Electrical Equipment】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500“

〇All electrical components except for the CDI are consolidated at the rear of the engine crankcase. It is easily accessible from either side of the vehicle, has good maintainability, and there is no need to reassemble even if you revert to the swing arm specification during vehicle inspection.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without any problems with LED turn signals. It supports 1 to 150 watts and can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

【Gasoline Tank Installation】

“Narrow Sportster Tank for Production”

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

•The rear area has been modified to the rigid frame line of yesteryear with a 13cm long hard tail kit. A flat fender, which is common, is well-balanced and mounted with effective reinforcement unique to SR on the back to withstand vibrations. It is a safe 6-point mount.

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made-to-order)

〇As the name suggests, it’s a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to make it a rigid line. You can revert to the swing arm/rear shock specification when you have a vehicle inspection or want to change the style.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇This is a kit that gives a powerful look with the same size as a typical Harley.

“Drilled plate torque rod SR400/500“

〇A drilled design torque rod to avoid interference with the wider tires.

“LOADSTAR TIRE　5.00-16“

〇A classic vintage style tire.

【Tail Lamp】

“Sparto Tail Lamp/Polish Japanese Number Standard”

〇The standard Sparto. Domestic numbers can be installed without modification. It was installed on the standard flat fender.

【Rear Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto a hardtail. Used as a blinker base.

【Drive System】

『Rear sprocket SR400/500 428-56 』

〇An affordable and durable replacement sprocket.