FrontHandlebars, F forks, headlights, etc.

【Front Fork】

“2%er 10cm long Joints for Front Fork (pair) [SR400/500]“

〇High-quality stainless steel fork joint.

【Front Tire】

“SHINKO flute 3.00-18”

〇A street tire with a vertical groove design. It helps to lighten the handling that tends to become heavy when long forks are used. It is a small, rounded 3.00 size.

【Headlight】

“5.75 inch Bates Light”

〇A headlight that fits well with the SR’s vehicle size and fork width, and can be installed without any discomfort.

“Bottom Mount Light Stay II“

〇A headlight stay that fits well with the chopper style due to its moderate height and protrusion. (5.75 inch Bates Light Set II SR400/SR500)

【Handle/Handle Area】

“Short Z Bar” (Discontinued)

“Amal type throttle holder, general purpose (for 7/8″)“

“Aluminum Short Brake Lever/Holder Set“

“Aluminum Short Clutch Lever/Holder Set“

〇This is a compact and easy-to-grip aluminum lever set.

“Handle Lock Weld On Kit“

● Attached to the less noticeable and easy-to-operate lower part of the stem.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle.

【Front Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style blinker.

『SR400/500 Bottom Mount narrow blinker stay』

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

〇A muffler that was custom-made for the rear part using a standard exhaust pipe in a slip-on specification. It has the same design as the complete sample.

【Seat】

“BATES Type Genuine Leather Solo/Pillion Set Vertical Tuck Roll“

〇A seat set made of genuine leather with good cushioning. The spring input position and angle are set, and the pillion pad mounting position is set in a way that is less tiring, unique to 2%ER.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat/Pillion Pad Set

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

〇A mount kit that is easy to install on custom frames and the like. The lever ratio can also be changed, allowing for good cushioning.

【Electrical】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500“

〇All electrical components except the CDI are consolidated at the rear of the engine crankcase. It is easy to maintain as it can be accessed with both hands from either side of the vehicle, and there is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without any problem with LED turn signals and supports 1-150 watts. It can also be used as a repro for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇It can be operated easily even while riding, and is welded and installed under the left side of the seat.

【Gasoline Tank Installation】

“Sportster Tank”

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body, insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter, change to rubber mount specification, and hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇A filter kit needed when removing the original air cleaner.

RearFenders, rear shocks, swingarms, etc.

• The rear area has been changed to the classic rigid frame line with a 13cm long hard tail kit. A flat fender, which is common, is well-balanced and installed after effectively reinforcing it to withstand the load of the sissy bar and the unique vibration of the SR. As an option, a one-off stainless steel sissy bar has been added.

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made-to-order)

〇As the name suggests, it’s a hardtail kit that can be attached and detached with bolts/nuts. It remodels the seat rail of the original frame to make it a rigid line. You can revert to the swing arm/rear shock specification when you go for vehicle inspection or when you want to change the style.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇A kit that gives a powerful look with the same size as a typical Harley. The owner selected white ribbon tires.

“Drilled plate torque rod SR400/500“

〇This is a drilled design torque rod to avoid interference with the wider tires.

【Tail Lamp】

“Sparto Tail Lamp/Polish Japanese Number Standard”

〇The standard Sparto. Domestic numbers can be installed without modification.

【Rear Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto a hardtail. Used as a blinker base.