FrontHandlebars, F forks, headlights, etc.

【Front Wheel】

“Front 19-inch Kit SR400/500 for Drum“

◯A 19-inch front wheel assembled with custom spokes on a rim diverted from other models. The tire is a replica of the old Pirelli tire.

【Headlight】

“5.75 inch Bates Light Chrome General Purpose“

〇A headlight that fits well with the SR’s vehicle size and fork width, and can be installed without any discomfort.

“SR Bottom Mount Light Stay“

〇It is installed with a headlight stay that is mounted low and close to the vehicle body.

【Handle/Handle Area】

“Loose Ride Bar Handle“

“Amal type throttle holder, general purpose (for 7/8″)“

“Handle Lock Weld On Kit“

● It is bolted on and installed at the bottom of the stem, which is inconspicuous and easy to operate.

【Switch】

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇A mini turn signal switch that is easy to install with a coupler on

(It is installed with modifications for different model years and small headlights)

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle.

【Turn Signal】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style turn signal.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm turn signal to the bottom of the frame.

【Speedometer】

Mechanical speedometer φ48mm [No trip 1:4] General purpose #General-purpose parts」

「Inside meter stay SR400/500」

◯It is installed on the left side of the stem, where it is inconspicuous and easy to see.

CenterTank, oil tank, seat, step, muffler etc.

The distinctive gas tank is a one-off item that has been narrowed down from a Harley Aermacchi gas tank. It’s a point that the owner was particularly particular about. It is safely mounted with a three-point rubber mount. The unique texture and custom paint design are by ‘BACON‘.

【Muffler】

“One-off pipe production exhaust flange set for SR“

〇We use a convenient mouthpiece kit for one-off exhaust manufacturing at the root.

“Universal Stainless Trumpet Muffler”

〇We attached the original silencer to the end of the one-off manufactured exhaust pipe.

【Seat】

“BATES Type Genuine Leather Solo/Pillion Set Vertical Tuck Roll“

〇A seat set made of genuine leather with good cushioning. The spring input position and angle settings, as well as the pillion pad mounting position, are set up in a unique, fatigue-resistant configuration by 2%ER.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat/Pillion Pad Set

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.

【Electrical】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500“

〇All electrical components except the CDI are consolidated at the rear of the engine crankcase. It is easily accessible from either side of the vehicle and is easy to maintain. There is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

“Battery Lesser“

〇This is a battery-less kit made entirely in Japan.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can handle 1-150 watts and can be used without difficulty even with LED turn signals. It can also be used as a replacement for the original relay.

“Custom Ignition Switch Weld On Kit General Purpose“

〇The main key, which is originally attached to the top bridge, is welded to the lower left of the seat for easy operation even while riding.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Other Center-Related Parts】
“Weld Tabs/Nuts and other Welding Parts” used in various parts
〇Gas Tank x Frame “Welding nut non-through M8 2p” (embedded in the tank), “Weld tab L size 4.5mm thick steel 2p“
〇Exhaust Pipe x Frame “Weld tab M size 4.5mm thickness 2p“
〇Seat x Frame “Welding nut non-through M8 2p” (used for spring seat), “Welding Tabs, 9mm Thickness, Steel, Size M, 2 Pieces“

RearFenders, rear shocks, swingarms, etc.

• A one-off sissy bar made with a hexagonal rod, arranged according to the owner’s request. The aging process for the fender and sissy bar was also requested from “BACON“, just like the gasoline tank.

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made to order)

〇As the name suggests, it’s a hardtail kit that can be attached and detached with bolts/nuts. It remodels the seat rail of the original frame to make it a rigid line. You can revert to the swing arm/rear shock specification when you change the style or during vehicle inspection.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇A kit that gives a powerful look similar to a typical Harley size. The ability to choose from many vintage pattern tires is also a popular feature of this menu.

“Drilled plate torque rod SR400/500“

〇A drilled design torque rod to avoid interference with the wider tires.

【Tail Lamp】

“Bee High Tail Light Chrome“

◯The combination of the classic flat fender and the “Beehive Tail Lamp”.

【Turn Signal】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style turn signal.

『Weld tab S size 4.5mm thick steel 2p』

〇Welded onto the hardtail. Used as a base for the turn signal.

【Other Rear Surrounding Used Parts】
“Welding Tabs/Nuts and other Welding Parts” used in various parts
〇Fender x Frame “Weld tab M size 4.5mm thickness 2p” x4
〇Torque Rod Receiving Boss “Weld Tornut M8“