FrontHandlebars, F forks, headlights, etc.

●The front area is finished with a standard Bates light and pullback handlebars on a front fork extended by 10cm. The turn signals are attached through a universal turn signal stay on the front side mount bolt under the engine.

---

【Front Fork】

“2%er 10cm long Joints for Front Fork (pair) [SR400/500]“

〇A front fork extended by 10cm.

---

【Front Tire】

“Pirelli MT53 Replica 4.00-18”

〇A replica of the 70s Pirelli. It suits all styles, from street to tracker, scrambler, bobber, chopper, and more.

---

【Headlight】

“5.75 inch Bates Light Black General Purpose“

“SR Bottom Mount Light Stay“

〇These are standard headlights and light stays.

---

【Handle, Around the Handle】

“2%er 70’s Pull-back Handle“

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1100mm ’88~’08“

“300mm Long Brake Cable“

“100mm Long Clutch Cable“

The handle is a standard pullback. We use long cables for the simple throttle.

---

【Switch】

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇A mini turn signal switch that is easy to install with a coupler on

(It is installed with modifications for different model years and small headlights)

---

“Handle Lock Weld On Kit“

〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.

---

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle.

---

【Front Blinker】

“Micro Blinker” (Discontinued ⇒ Now changed to Star Bean Blinkers, Set of 2, Black)

“Universal Blinker Stay 10A Type Steel”

〇The ultra-small micro blinker is installed on the front side of the lower part of the engine mount.

---

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.

CenterTank, oil tank, seat, step, muffler etc.

●The gasoline tank is a peanut tank that is safely mounted on three points with rubber. The tasteful aging paint was requested from “BACON“. The frame under the seat is rebuilt to match the angle of the “Hardtail Kit” at the rear, considering strength, precision, durability, and maintainability, by cutting the original part and using thick steel pipes.

---

【Muffler】

“Torque cone drag pipe muffler SR400/500“

It is a full exhaust muffler with a torque cone developed in-house in the mouthpiece.

---

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes the riding posture cool and the position extremely less tiring.

---

【Seat】

“BATES Type Genuine Leather Solo/Pillion Set Vertical Tuck Roll“

〇A seat set with good cushioning made of genuine leather. The spring input position and angle settings, and the pillion pad mounting position are set in a way that is unique to 2%ER and reduces fatigue.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat/Pillion Pad Set

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

---

【Kick Pedal】

“Chrome Kick Pedal“

〇 It’s an accent part that makes it easier to kick by increasing the area and making it easier to apply body weight.

---

【Electrical Equipment】

“SR400/500 Custom Electrical Plate #2%er Original #SR400/500“

〇All electrical components except for the CDI are consolidated at the rear of the engine crankcase. It is easily accessible from either side of the vehicle and has good maintainability. There is no need to reassemble even if you return to the swing arm specification during vehicle inspection.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without difficulty even with LED turn signals. It can also be used as a repro for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇Easy to operate even while riding, welded on the lower left of the seat.

---

【Engine Area】

“Stock replica manifold SR400/500“

〇It is a cheap replica specification for genuine replacement.

“Breather filter SR400/500“

〇It is a filter kit necessary when removing the genuine air cleaner.

---

【Gasoline Tank Installation】

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on the front side.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also enlarges the hole diameter and is used with a rubber mount.

---

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

●The rear area uses a hardtail kit (13cm long) that determines the overall styling, a common flat fender, a cross design specified by the owner, and a one-off production sissy bar.

---

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made to order)

〇As the name suggests, this is a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to make it rigid line. You can revert to swing arm/rear shock specification when you need to change the style or for vehicle inspection.

---

【Rear Tire】

“Pirelli MT53 Replica 4.00-18”

〇A replica of the 70s Pirelli. It suits all styles, from street to tracker, scrambler, bobber, chopper, and more.

---

【Tail Lamp】

“Old Spalt Taillight Polish“

“Old Sparto Tail Reinforced Number Base“

〇We have selected a tail with a vintage feel.

---

【Rear Blinker】

“Micro Blinker” (Discontinued ⇒ Now changed to Star Bean Blinkers, Set of 2, Black)

〇Ultra-small, powerful LED mini blinker.

“Weld Tab A Type for Blinker Stay”

〇Welding stay for up to 6mm mounting blinker.

---

【Drive System】

“Rear sprocket SR400/500 428-56“

〇An affordable and durable replacement sprocket.