Home » #260 SR400

#260 SR400

2022.10.30

Custom Bike

#260 SR400Custom Report

The base car that was brought in before was customized to №169. It was once finished before, but it is an SR400 hardtail that was completed with additional customizations such as fork extension and various parts. We created it as a long fork chopper style with a beautiful silhouette. The owner himself was involved in the additional customization, and the paint of the tank and fender, and the muffler are made by the owner. The sissy bar, which has become a little taller than at the time of №169, is a gift from 2%ER as a celebration of the owner’s marriage and childbirth.

【See the appearance before customization, when it was №165 here】

【The STD Hardtail Complete that became the base, sample car is here】

【Over 80 hardtail production examples are here】

Custom List

FrontHandlebars, F forks, headlights, etc.

●The front area has been extended by 30cm in true Chopper style. The front wheel has been upgraded to 21 inches.

【Front Fork Area】

“2%er 15cm long Joints for Front Fork (pair) [SR400/500]“

〇High-quality stainless steel fork joint.

“SR400/500 15cm long inner tube kit“

〇A fork tube kit that allows you to extend the front more safely.

“2%er Tweak Bar (front stabilizer) [SR 400/500]“

〇A stabilizer that is extremely effective in correcting the handling that tends to lag one beat behind with the extended fork.

“Welding Side Stand Extension Plate”

〇A plate for extending the side stand that leans too much when the fork is extended. Welding is required. (The one on the vehicle is a prototype)

【Headlight】

“5.75 inch Bates Light Chrome General Purpose“

〇A headlight that fits well with the SR’s vehicle size and fork width, and can be installed without any discomfort

“Bottom Mount Light Stay II“

〇A headlight stay that fits well with the chopper style due to its moderate height and protrusion

【Handle/Handle Area】

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 900mm ’88~’08“

〇The handle is a custom-made riserless T-bar. The switch to the Amal throttle has made it even simpler than usual. Long cables are used for each.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle

【Turn Signal】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style turn signal.

【Speedometer】

“48φ Mechanical Speedometer”

〇Mounted on the left front side of the gasoline tank, which is not easily noticeable and has high visibility

“Extension meter cable joint“

〇Used when extending the fork or relocating the meter

CenterTank, oil tank, seat, step, muffler etc.

●The Narrow Sports Star Tank is safely mounted with three rubber points. The frame under the seat is cut from the original part, and considering strength, precision, durability, and maintainability, it is rebuilt to match the angle of the rear “Hardtail Kit“.

【Muffler】

〇Drag pipe muffler attached to the owner’s homemade normal exhaust pipe

【Step/Shift】

“Mid-High Jockey Shift Kit/Parkarize”

〇Maintaining the comfortable riding posture of the mid-high step, this is a jockey shift kit that focuses on operation feel such as touch and stroke

【Gasoline Tank Installation】

“Narrow Sportster Tank for Production”

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body, insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.

【Seat】

“BATES Type Genuine Leather Solo Saddle Seat Vertical Tuck Roll Black/White“

〇A genuine leather solo saddle seat with a balanced price, look, and comfort. It is installed with a soft ride that is hard to bottom out by changing the mounting angle and spring input position.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat Black

“Solo Saddle Seat 2 Inch Spring Comfort Mount Set”

〇A mount kit that is easy to install on custom frames and the like. You can also change the lever ratio and create a good cushioning effect.

“BATES Type Genuine Leather Pillion Pad”

〇Installed not for tandem but at a position that becomes a stopper for the upper body weight during acceleration. Long-distance running becomes significantly easier.

(Discontinued) ⇒Genuine Leather STD Solo Saddle Seat/Pillion Pad Set

【Carburetor】

『FCR carburetor 39φ SR400/500 single unit』

〇Your slow SR will drastically change. It’s a carburetor that’s easy to handle with sharp and smooth acceleration. ※Dedicated manifold set for installation, coming soon.

『Net funnel set for FCR carburetor』

〇This is a set of an aluminum funnel, changed from a red plastic funnel, and a stainless steel trash prevention net.

【Electrical Equipment】

69 box SR400/500 MOTORROCK electrical box

〇An oil tank-style electrical box that can be attached to the original frame.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can handle 1-150 watts and can be used without difficulty with LED turn signals. It can also be used as a replacement for the original relay.

【Engine Area】

“AIS Cancel Plate”

〇A cancel plate made of stainless steel. It is also possible to use it by sandwiching it without removing the AIS body.

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

【Side Stand】

“Weld-on Side Stand Extension Plate“

〇A side stand extender that you cut to your preferred length and attach by welding.

RearFenders, rear shocks, swingarms, etc.

●The rear area is finished with a 13cm long hardtail kit, 16-inch wheels, a flat fender with safe reinforcements on the back, old-school tail lights, and a one-off custom-made sissy bar.

【Hardtail】

『“Rigid Line” Bolt-On Hardtail Kit』(13cm long, made to order)

〇As the name suggests, this is a detachable hardtail kit using bolts/nuts. It remodels the seat rail of the original frame to make it a rigid line. You can revert to a swing arm/rear shock specification when you need to change the style or during vehicle inspection.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“