Home » #316 SR400

#316 SR400

2024.8.13

Custom Bike

#316 SR400Custom Report

An SR400 long fork style assembled entirely with bolt-on parts.

We used a standard vehicle as a base, keeping the front and rear fenders, seat, and gas tank (paint) as is,

and replaced with the bare minimum bolt-on parts,

.A chopper-like silhouette

.Fun ride

.Position and handling that doesn’t tire you out

We aimed for these and produced it.

■About Vehicle Inspection

.Change of F turn signal position

.Muffler replacement or core filling

.Addition of tandem belt

.Addition of left mirror

.Addition of reflector

Custom List

FrontHandlebars, F forks, headlights, etc.

●The front end with a long fork typical of 2%ER is nicely handled with a vintage replica 10-inch pullback handle, mounted in the best position with a Paughco type 3-inch square riser.

The controls are standard clean treatment, and the clutch lever has been removed by converting to a jockey shift, making it even simpler.

【Front Fork Area】

“10cm Long Fork Joint” (For use without valve) ¥17,800

〇High-quality stainless steel fork joint.

“SR400/500 15cm long inner tube kit” ¥62,000

〇A fork tube kit that allows you to extend the front more safely.

“2%er Tweak Bar (front stabilizer) [SR 400/500]” ¥17,500

〇A stabilizer that is extremely effective in correcting the handling that tends to lag behind the extended fork.

“Fork boots, general-purpose” ¥2,800

〇Classic universal fork boots.

“Welding Side Stand Extension Plate” ¥3,200

〇A plate for extending the side stand that leans too much when the fork is extended. Welding is required.

【Headlight】

“5.75 inch Bates Light HS Type Black Body/Chrome Rim Universal”¥10,500

〇This is a Bates light for custom vehicles with a harness storage type that can store many harnesses and couplers inside the light.

“SR Bottom Mount Light Stay” ¥2,500

〇A classic headlight that fits well with the SR’s vehicle size and fork width. It is installed with a headlight stay that mounts low and close to the vehicle body.

【Handle/Handle Area】

“Vintage Replica 10″ Pullback Handle 22.2mm (7/8″)“　￥10,500

◯ This is a vintage replica handlebar in a chopper style, with attention to the angle of rise and the droop of the handle.

“Flanders Replica Riser 2.5 Inch” ￥25,700

◯ A Flanders replica riser with a great atmosphere

“Trail Enduro Grip”￥1,300

“Amal type throttle holder, general purpose (for 7/8″)” ￥4,180

(This vehicle uses a vintage Tomazelli, chain pull throttle)

Amal type slot wire 1100mm ’88~’08￥2,750

“Brake Hose 1300mm One-off Item”

“MOTOR ROCK Decompression lever” ¥4,500

〇 A decompression lever directly attached to the engine to simplify the handle area.

【Meter】

“Inside Meter Kit”¥14,300

〇A meter kit that can be bolted on the inside of the fork when viewed from the front, specifically for small tanks.

“Meter Cable Extension Joint 30cm”¥1,900

【Turn Signal】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose” ¥7,000

〇A classic among classics. A chopper-style turn signal.

“SR400/500 Bottom Mount narrow blinker stay” ¥5,800

〇A stay to attach a 10mm turn signal to the bottom of the frame.

CenterTank, oil tank, seat, step, muffler etc.

●A center area enhanced for less fatigue and more enjoyable rides, featuring steps that allow for a moderate bend in the knees and weight distribution, a seat with high cushioning, and an FCR carburetor that dramatically changes the SR’s performance.

【Step/Shift】

“Mid-High Jockey Shift Kit/Parkarize”　¥82,500

〇The jockey shift kit, which is particular about the touch and stroke operation, maintains the comfortable riding posture of the mid-high step.

【Muffler】

『Torque cone drag pipe muffler SR400/500』¥36,000

〇This is a full exhaust muffler with a torque cone that we developed in-house built into the mouthpiece. It is made at an angle that suits any style, such as a normal frame or hardtail.

【Seat】

“Old school bucket double seat SR400/500” (Custom White Leather) ¥45,500

◯ This is the most comfortable seat among the 2%ER originals, which holds around the hip bone.

【Carburetor】

“FCR carburetor 39φ SR400/500 single unit” ¥77,000

〇Your slow SR will be dramatically transformed. It’s a carburetor that’s easy to handle with sharp and smooth acceleration.

“Funnel Net for FCR Carburetor” ¥3,900

〇It’s a set of stainless steel trash prevention nets that you sandwich between the body and the funnel.

“Manifold Kit for FCR39φ” ¥12,000

〇It’s a dedicated adapter to firmly fix the FCR carburetor to the SR400/500.

【Electrical Equipment】

“IC blinker relay wide range specification” ¥2,400

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

“Battery Lesser” ¥3,400