FrontHandlebars, F forks, headlights, etc.

【Headlight】

“5.75 inch Bates Light Black Body/Chrome Rim”

“SR Bottom Mount Light Stay“

〇A classic headlight that matches well with the SR’s vehicle size and fork width. It is installed with a headlight stay that mounts low and close to the vehicle body.

【Handle/Handle Area】

◯The handle is a one-off made of stainless steel.

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1100mm ’88~’08“

“Brake Wire 100mm Long“

“Clutch Wire 100mm Long“

〇We are using long cables for the simple throttle.

“Handle Lock Weld On Kit“

〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Matte Black 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the frame bottom.

【Speedometer】

『Mechanical Speedometer 60mm Black Panel 1:4』

〇A standard small meter. It comes with a trip meter.

『Universal Speedometer Stay』

〇It is mounted on the front left side of the gas tank, where it is inconspicuous and highly visible.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

◯One-off stainless steel muffler.

【Seat】

◯Universal solo seat with seat rail drop processing.

【Gasoline Tank Installation】

◯ One-off peanut tank. Installed with a three-point rubber mount.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.

【Electrical Equipment】

“IC blinker relay wide range specification“

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇The main key, which is originally attached to the top bridge, is easy to operate even while riding, and is welded and installed under the left side of the seat.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Shock】

“280mm G-Suspension”

●A rear shock that is about 4cm lower. It moves well among low-down suspensions.

【Rear Blinker】

Small Bullet Turn Signal Matte Black 4pcs SET General Purpose

〇A classic among classics. A chopper-style blinker.

“Rear Bottom Mount Blinker Stay”

〇A stay to attach the blinker to the swing arm.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.