#83 SR400

Custom Bike

#83 SR400Custom Report

Frisco / SR Chopper created with the image of SO-CAL streets.

Due to the owner’s profession, it is designed to pass inspection with just an inner baffle in the muffler and a left mirror and reflector, despite this style.

 

[ Overall Silhouette ]

Front fork extended by 10cm, swing arm extended by 5cm,

280mm Low Down Suspension] G-SUSPENSION280 [Chrome] General-purpose #SR400/500, seat rail drop processing.

 

( Click here for the article published in THE SR TIMES )

( Click here for the related blog article )

 

Cookie consent is required to display this video.

 

Cookie consent is required to display this video.

Custom List

FrontHandlebars, F forks, headlights, etc.

Front Fork

2%er 10cm long Joints for Front Fork (pair) [SR400/500]

〇High-quality stainless steel fork joint.

Fork boots, general-purpose

〇Classic universal fork boots.


Front Wheel

2%er Front Wheel Aluminum Hub Cap [SR400/500]

〇You can change to a classical style by sticking it on a normal drum brake.


Headlight

“Sportster Type Headlight”

〇A headlight with a visor and a bright H4 bulb. It’s a convenient headlight that can store a lot of wiring in the body.


Handle/Handle Area

◯ A custom handle made of stainless steel, focusing on the owner’s comfort.

SR400/500 Handlepost Offset Collar

◯ Using an offset color, the handle is raised a little from the back than usual.

Amal type throttle holder, general purpose (for 7/8″)

Amal type slot wire 1100mm ’88~’08

[Special long brake wire for SR drum brake] 400mm

Clutch Wire 300mm Long

〇 Using each long cable for a simple throttle.

Switch

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇 A mini turn signal switch that is easy to install with a coupler on.


Handle Lock Weld On Kit

〇We have newly installed a handle lock under the stem, which is inconspicuous and easy to operate.


MOTOR ROCK Decompression lever

A decompression lever directly attached to the engine to simplify the handle area. (The one on the vehicle is an old model)


Front Blinker

Small Bullet Turn Signal Chrome 4pcs SET General Purpose

〇A classic among classics. A chopper-style blinker.

SR400/500 Bottom Mount narrow blinker stay

〇A stay to attach a 10mm blinker to the bottom of the frame.


Speedometer

Mechanical Speedometer 60mm Black Panel 1:4

Universal Speedometer Stay

〇Mounted on the left front side of the gasoline tank where it is inconspicuous and highly visible.

Extension meter cable joint

〇Used when extending the fork or relocating the meter.


CenterTank, oil tank, seat, step, muffler etc.

Muffler

“Exhaust Pipe Flange Set for One-off Pipe Production”

Custom Exhaust Fabrication Ripple Pipe, 45mm (1-3/4″) Diameter

〇A one-off made using a convenient production kit for the mouthpiece at the root. It’s a shotgun style that avoids the rear shock, with ripple processing in the middle as an accent. It is finished in steel plating.


Step

Mid-High Control Parkerized for SR400/500

〇This step kit is essential for 2%ER’s custom that makes your riding posture cool and extremely less tiring. The step bar has been changed to an Anderson replica.


Seat

◯A one-off solo seat. We’ve cleverly designed it so that the necessary gap to avoid interference with the fender during rear shock stroke is less noticeable. We used thick thread for the stitches to create a rough diamond pattern.


Electrical Equipment

IC blinker relay wide range specification

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

Battery Lesser

〇This is a battery-less kit made entirely in Japan.

Custom Ignition Switch Weld On Kit General Purpose

〇Easy to operate even while riding, it is welded and installed under the left side of the seat.


Gasoline Tank Installation

“Narrow Sportster Tank for Manufacturing”

◯ It was securely fixed with a three-point rubber mount. The lime green paint goes well with the chrome fender.

Welding nut non-through M8 2p

〇 Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

Weld tab M size 4.5mm thickness 2p

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

Weld tab L size 4.5mm thick steel 2p

〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.


Engine Area

Breather filter SR400/500

〇This is a filter kit needed when removing the original air cleaner.


Drive System

Front sprocket SR400/500 428-19

〇A durable replacement sprocket made of steel.


  • RearFenders, rear shocks, swingarms, etc.

    Rear Tire

    LOADSTAR TIRE 4.00-18

    ◯ A classic watermelon pattern, high-profile vintage style tire. Selected a size narrower than the usual 4.50 size used for the rear. This suits choppers well.


    Rear Shock

    “280mm G-Suspension/Chrome”

    〇A rear shock that lowers by about 4cm. It moves well among low-down suspensions. (Removal of the original chain case is necessary)


    Rear Fender

    5-Inch Custom Rib Fender – Steel Material

    Reinforcement Back Plate for 5-Inch Rib Fender

    ◯The chrome-finished rib fender is one-of-a-kind. There are rumors that the sissy bar will break on the SR, but we have effectively reinforced the back with suitable materials to safely mount the sissy bar.


    Sissy Bar

    ◯The sissy bar body is also one-off. It is made of steel and finished with chrome plating.


    Tail Lamp

    Lucas tail lamp with pedestal Japanese standard number size

    ◯A tail lamp that is easy to use with a Japanese standard number size, while having the nice atmosphere of an imported body.


    Rear Blinker

    Small Bullet Turn Signal Chrome 4pcs SET General Purpose

    〇A classic among classics. A chopper-style blinker.

    Weld tab S size 4.5mm thick steel 2p

    〇Welded onto a hardtail. Used as a blinker base.


    Drive System

    Rear sprocket SR400/500 428-56

    〇An affordable and durable replacement sprocket.

    ※Parts Reference may show similar products or products with additional processing.