FrontHandlebars, F forks, headlights, etc.

【Front Fork】

◯The front fork is lowered. It is designed and constructed to maintain good movement while preventing bottoming out.

【Front Tire】

【LOADSTAR TIRE 4.00-18】

◯ A classic watermelon pattern, a vintage style tire with height.

【Headlight】

“7 inch Lucas Type Headlight Case Black“

〇A standard 7-inch diameter, bullet-shaped headlight case (painted) for cafe racer style. The light stay is drilled from WM made.

“Three-point headlight lens Lucas type 7 inch H4“

◯The rounded lens shape and the built-in three-point create a superb vintage and classical atmosphere.

【Handle/Handle Area】

◯ The top bridge is made by WM. The stays are smoothed and buffed for a simple finish.

“CHUCK BOX Ace Bar Handle”

〇 A very thick stainless steel, extremely simple handmade separate handle. It is a custom specification and is slightly longer.

“Amal type throttle holder, general purpose (for 7/8″)“

〇 A very simple, classic vintage style throttle.

“Amal type slot wire 800mm ’88~’08“

“Brake wire/100mm 200mm 300mm 600mm SR400/500 #SR400/500“

“Clutch wire/300mm 200mm 100mm standard SR400/500 ALL YEARS“

【Switch】

“Mini Turn Signal Switch Coupler On Kit (’85~00)”

〇 A mini turn signal switch that is easy to install with a coupler on.

“Handle Lock Weld On Kit“

〇We have newly installed a handle lock under the stem, which is inconspicuous and easy to operate.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

” Inside meter kit for drum brake SR400/500 #2%er Original #SR400/500“

◯ It’s a speedometer kit that doesn’t stand out and doesn’t ruin the style, but has good visibility while riding.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“Fishtail End Tip“

◯The short fishtail muffler is one-off. Added drilled processing.

【Step】

“Mid-High Control Parkerized for SR400/500“

〇A cool riding posture and a position that is extremely less tiring are essential for the 2%ER’s custom. This vehicle is equipped with a one-off machined peg.

【Seat】

◯The seat is a mysterious, flavorful vintage solo saddle.

【Gasoline Tank Installation】

◯ A one-off tank with a normal tank processed into A, J, S style according to the style, center rib processing, and Harley cap relocated.

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for rear gas tank installation. This also enlarges the hole diameter and uses it as a rubber mount.

【Electrical Equipment】

“IC blinker relay wide range specification“

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that is made entirely in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇The main key, which is originally attached to the top bridge, is easy to operate even while riding, and is welded and installed on the lower left of the seat.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇This is a kit that gives a powerful look with the same size as a typical Harley.

“LOADSTAR TIRE　5.00-16“

〇A classic vintage style tire.

“Drilled plate torque rod SR400/500“

〇A drilled design torque rod to avoid interference with the wider tire.

【Rear Shock】

“280mm G-Suspension/Black”

〇A rear shock that lowers by about 4cm. It moves well among low-down suspensions.

【Rear Fender】

◯The short fender made of steel is one-off.

【Tail Lamp/Number Plate】

◯A custom-made right-side number plate using the DUO tail lamp.

【Rear Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto a hardtail. Used as a blinker base.

【Drive System】

『Rear sprocket SR400/500 428-56 』

〇An affordable and durable replacement sprocket.