FrontHandlebars, F forks, headlights, etc.

【Front Fork Area】

“2%er 15cm long Joints for Front Fork (pair) [SR400/500]“

〇High-quality stainless steel fork joint.

【Front Tire】

『LOADSTAR TIRE 4.00-18』

〇A classic watermelon pattern, a vintage style tire with height.

【Headlight】

“[Triangle Head Light Chrome] Triangle Headlight General Purpose“

◯Mounted with a one-off light stay.

【Handle/Handle Area】

◯ A narrow, one-off handle for a unique face area.

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1200mm ’88~’08“

“Brake Wire 200mm Long“

“Clutch Wire 100mm Long“

〇 We are using long cables for the simple throttle.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the handle area. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank where it is inconspicuous and highly visible.

“Extension meter cable joint“

〇Used when extending the fork or relocating the meter.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

◯The upsweep fishtail muffler is also a one-off production.

【Seat Rail】

◯The seat rail is drop-processed. By bending the frame that supports the suspension receiver on the front side, it is even more lowered than usual.

【Gas Tank Installation】

◯ The gas tank is a one-off Sportster type with a three-point rubber mount support.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gas tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.

【Electrical Equipment】

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can handle 1-150 watts without any problem, even for LED turn signals. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that is made entirely in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇Originally attached to the top bridge, the main key is easy to operate even while riding, and is welded to the lower left of the seat.

【Engine Area】

“Breather filter SR400/500“

〇A filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Shock】

“280mm G-Suspension/Black”

●A rear shock that lowers by about 4cm. It moves well among low-down suspensions. (Removal of the original chain case is necessary)

【Rear Tire】

“LOADSTAR TIRE 4.50-18“

〇A classic vintage style watermelon pattern. It’s a rear tire with height and volume.

【Rear Fender】

◯The rear fender is one-off. It was mounted on the swing arm.

【Rear Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style blinker.

『Rear Bottom Mount Blinker Stay』

〇A stay to attach the blinker to the swing arm.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.