#54 SR400Custom Report
Considering vehicle inspection, this SR was made to look like a rigid frame. If you replace the rigid suspension with a spring shock, it will pass the vehicle inspection.
The vehicle size was made larger with a one-off handle that carefully matched the position, extending the swing arm by 7cm to suit the tall owner.
Even in a rigid state without a rear shock, we made it easy to ride by carefully discussing and producing the position and direction of the steps and seats.
The front and rear tires are “Firestone”. It suits the simple exterior well.
Custom List
FrontHandlebars, F forks, headlights, etc.
【Front Tire】
◯ It’s a classic watermelon pattern, a vintage style tire with height.
【Headlight】
“5.75 inch Bates Light Black Body/Chrome Rim”
〇A classic headlight that matches well with the SR’s vehicle size and fork width. It was mounted a little higher to match the increased vehicle size.
【Handle/Handle Area】
◯ Directly attached, one-off handle made of hand-bent steel.
“Amal type throttle holder, general purpose (for 7/8″)“
“Amal type slot wire 1200mm ’88~’08“
〇 We are using long cables for the simple throttle.
〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.
“MOTOR ROCK Decompression lever“
〇 A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)
【Front Blinker】
“Small Bullet Turn Signal Matte Black 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
“SR400/500 Bottom Mount narrow blinker stay“
〇A stay to attach a 10mm blinker to the frame bottom.
【Speedometer】
“Mechanical Speedometer 60mm Black Panel 1:4“
〇Mounted on the left front side of the gasoline tank, which is inconspicuous and highly visible.
CenterTank, oil tank, seat, step, muffler etc.
【Step】
“Mid-High Control Parkerized for SR400/500“
〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.
【Seat Rail】
◯The underframe of the seat is drop-processed with a rigid line.
【Electrical Equipment】
“IC blinker relay wide range specification“
〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.
〇This is a battery-less kit that is made entirely in Japan.
“Custom Ignition Switch Weld On Kit General Purpose“
〇Easy to operate even while riding, it is welded and attached to the lower left of the seat.
【Gasoline Tank Installation】
◯ A one-off tank that has been narrowed and tunnel-processed for the Sportster. Mounted with three rubber points.
“Welding nut non-through M8 2p“
〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.
“Weld tab M size 4.5mm thickness 2p“
〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.
“Weld tab L size 4.5mm thick steel 2p“
〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.
【Engine Area】
〇This is a filter kit needed when removing the original air cleaner.
【Drive System】
“Front sprocket SR400/500 428-19“
〇A durable replacement sprocket made of steel.
RearFenders, rear shocks, swingarms, etc.
【Rear Shock】
◯We extended the swingarm by 7cm and fixed it with a rigid suspension at the top and bottom, modifying it to look like a rigid frame.
【Rear Tire】
〇A classic vintage style watermelon pattern. It’s a rear tire with height and volume.
【Rear Blinker】
Small Bullet Turn Signal Matte Black 4pcs SET General Purpose
〇A classic among classics. A chopper-style blinker.
“Weld tab S size 4.5mm thick steel 2p“
〇Welded onto the hardtail. Used as a blinker base.
【Drive System】
“Rear sprocket SR400/500 428-56“
〇A durable sprocket made of steel.
〇A replacement drive chain with built-in O-rings.
※Parts Reference may show similar products or products with additional processing.