FrontHandlebars, F forks, headlights, etc.

【Front Fork Area】

“2%er 15cm long Joints for Front Fork (pair) [SR400/500]“

〇High-quality stainless steel fork joint.

“SR400/500 15cm long inner tube kit“

〇A fork tube kit that allows you to extend the front more safely.

“2%er Tweak Bar (front stabilizer) [SR 400/500]“

〇A stabilizer that is extremely effective in correcting the handling that tends to lag behind the extended fork.

“Fork boots, general-purpose“

〇Classic universal fork boots.

【Front Wheel】

“SR400/500 21inch kit for front“

〇A wheel kit that results in a narrow, large-diameter, sharp style.

“2%er Front Wheel Aluminum Hub Cap [SR400/500]“

〇You can change to a classic style by sticking it on a normal drum brake.

【Headlight】

◯A one-off light stay with a twisted square rod and a dead stock square light. The interior has been modified to change to an H4 bulb. It lights up well and is reassuring.

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“Tapered Fish Tail Muffler“

◯A one-off custom-made up muffler. A fish tail is attached to the end.

【Step】

“One-off Mid-High Step”

Similar products are here↓

“Mid-High Control Parkerized for SR400/500“

【Electrical Equipment】

“IC blinker relay wide range specification“

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that is made entirely in Japan.

“Custom ignition switch bolt-on kit General-purpose“

〇The main key, which is originally attached to the top bridge, is easy to operate even while riding, and is installed on the lower right of the seat.

【Gasoline Tank Installation】

“Welding nut non-through M8 2p“

〇Drill a hole in the gasoline tank body and insert it for welding. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Tail Lamp】

“Bee High Tail Light Chrome“

【Sissy Bar】

◯The Sissy Bar is also a one-off production. Considering the weight, the two bars on the outside are square bars, and the two in the middle are made using hollow square pipes.

【Rear Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto a hardtail. Used as a blinker base.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.