#4 SR400

Custom Bike

#4 SR400Custom Report

〇 ” Bobber/Compact Chopper Complete ” is the base, with an extended swingarm and FCR carburetor for a higher level of style and performance. You won’t get tired even when going to the convenience store in a relaxed position.

 

〇 ” Click here for THE SR TIMES article

 

〇 ” Click here for the owner’s snap

 

Custom List

FrontHandlebars, F forks, headlights, etc.

Front Fork

◯The front fork is lowered by 3cm. The bottom case is painted black.


Front Tire

LOADSTAR TIRE 4.00-18

〇A classic watermelon pattern, a vintage style tire with height.


Headlight

“5.75 inch Bates Light Black Body/Chrome Rim”

SR Bottom Mount Light Stay

〇A classic headlight that matches well with the SR’s vehicle size and fork width. It is installed with a headlight stay that mounts low and close to the vehicle body.


Handle/Handle Area

◯A slightly wide continental handle.

Amal type throttle holder, general purpose (for 7/8″)

Amal type slot wire 1100mm ’88~’08

Brake Wire 100mm Long

Clutch Wire 100mm Long

〇We are using each long cable for a simple throttle.


Handle Lock Weld On Kit

〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.


MOTOR ROCK Decompression lever

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)


Front Blinker

Small Bullet Turn Signal Chrome 4pcs SET General Purpose

〇A classic among classics. A chopper-style blinker.


Speedometer

Mechanical Speedometer 60mm Black Panel 1:4

Universal Speedometer Stay

〇Mounted on the left front side of the gasoline tank, which is inconspicuous and highly visible.


CenterTank, oil tank, seat, step, muffler etc.

Muffler

Torque cone drag pipe muffler SR400/500

〇It is a full exhaust muffler with a torque cone developed independently in the mouthpiece.


Step

Mid-High Control Parkerized for SR400/500

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and significantly reduces fatigue.


Carburetor

FCR carburetor 39φ SR400/500 single unit

〇The sluggish SR will dramatically change. It’s a carburetor that’s easy to handle, with sharp and smooth acceleration and good startability.

SR400/500 FCR 39φ carburetor mounting adapter set

〇It’s a dedicated adapter to firmly fix the FCR carburetor to the SR400/500.

“Funnel Net for FCR Carburetor”

〇It’s a net to prevent debris that could cause major damage to the engine while maintaining smooth air intake resistance.


Seat

◯Old School Solo Seat.


Electrical Equipment

IC blinker relay wide range specification

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

Battery Lesser

〇A battery-less kit that is made entirely in Japan.


Gasoline Tank Installation

◯ One-off peanut tank. Installed with a 3-point rubber mount.

Welding nut non-through M8 2p

〇 Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

Weld tab M size 4.5mm thickness 2p

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

Weld tab L size 4.5mm thick steel 2p

〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.


Engine Area

Breather filter SR400/500

〇A filter kit needed when removing the original air cleaner.


Drive System

Front sprocket SR400/500 428-19

〇A durable replacement sprocket made of steel.


  • RearFenders, rear shocks, swingarms, etc.

    Rear Shock

    “280mm G-Suspension/Black”

    〇With a swing arm extended by 5cm, and a rear shock that’s about 4cm down. It moves well among low-down suspensions.


    Rear Tire

    LOADSTAR TIRE 4.50-18

    〇A classic vintage style with a watermelon pattern. It’s a rear tire with height and volume.


    Rear Fender

    5-Inch Custom Rib Fender – Steel Material

    Reinforcement Back Plate for 5-Inch Rib Fender

    〇A thick and durable rib fender. We have added a reinforcement plate around the mounting holes to make it even more robust.


    Tail Lamp

    “Sparto Tail Lamp/Polish Japanese Number Standard”

    〇The standard Sparto. Domestic numbers can be installed without any modifications.


    Rear Blinker

    Small Bullet Turn Signal Chrome 4pcs SET General Purpose

    〇A classic among classics. A chopper-style blinker.


    Drive System

    Rear sprocket SR400/500 428-56

    〇A durable sprocket made of steel.

    ※Parts Reference may show similar products or products with additional processing.