FrontHandlebars, F forks, headlights, etc.

【Front Fork】

◯The front fork is a black springer used from another vehicle.

【Front Wheel】

“SR400/500 21inch kit for front“

〇A wheel kit that results in a narrow, large-diameter, sharp style.

【Handle/Handle Area】

“2%er 70’s Pull-back Handle“

“Amal type throttle holder, general purpose (for 7/8″)“

◯We are using long cables with a simple throttle.

“Handle Lock Weld On Kit“

〇We have newly installed a handle lock under the stem, which is inconspicuous and easy to operate.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

“Mechanical Speedometer 60mm Black Panel 1:4“

“Universal Speedometer Stay“

〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.

“Extension meter cable joint“

〇Used when extending the fork or relocating the meter.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“One-off Pipe Manufacturing Exhaust Pipe Flange Set”

“Universal Stainless Trumpet“

〇A one-off muffler made using a convenient manufacturing kit for the mouthpiece at the root. A trumpet is used for the silencer.

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.

【Seat】

◯A one-off bucket seat is placed on the drop-processed seat rail. Not only the style, but also the footing has improved, making it easier to handle.

【Electrical】

“Battery Lesser“

〇This is a battery-less kit made entirely in Japan.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can handle 1-150 watts and can be used without any problems with LED turn signals. It can also be used as a replacement for the original relay.

“Custom Ignition Switch Weld On Kit General Purpose“

〇The main key, which is originally on the top bridge, can be easily operated even while riding, and is welded and installed on the lower left of the seat.

【Gasoline Tank Installation】

◯ The gasoline tank with a rib in the center is one-off.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇A kit that gives a powerful look with the same size as a typical Harley.

“LOADSTAR TIRE　5.00-16“

〇A classic vintage style tire.

“Drilled plate torque rod SR400/500“

〇A drilled design torque rod to avoid interference with the wider tire.

【Rear Shock】

◯The swing arm has been extended by 7cm. The rigid suspension is custom-made.

【Rear Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto a hardtail. Used as a blinker base.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.