#30 SR400

Custom Bike

#30 SR400Custom Report

SR Bobber.

The overall silhouette is 2cm lower at the front, with a “Slim Short Suspension” for rear lowering, seat rail drop processing, and the rear wheel is 16″ Kit Steel Spoke SR400/500 Rear.

 

We combined used parts that were lying around in the shop with the owner, who is a welder, to make it a bit more rugged.

Custom List

FrontHandlebars, F forks, headlights, etc.

Front Fork

◯Front lowered by 2cm.


Front Tire

LOADSTAR TIRE 4.00-18

〇A classic watermelon pattern, high vintage style tire.


Headlight

◯The tractor light is mounted a little higher than usual.


Handle/Handle Area

◯The handle is a hand-bent one-off.

Amal type throttle holder, general purpose (for 7/8″)

Amal type slot wire 1200mm ’88~’08

300mm Long Brake Cable

200mm Long Clutch Cable

〇We are using each long cable for a simple throttle.


MOTOR ROCK Decompression lever

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)


Front Blinker

Small Bullet Turn Signal Chrome 4pcs SET General Purpose

〇A classic among classics. A chopper-style blinker. Attached to the frame bottom.


Speedometer

Mechanical Speedometer 60mm Black Panel 1:4

Universal Speedometer Stay

〇Mounted on the left front side of the gasoline tank, which is inconspicuous and has high visibility.


CenterTank, oil tank, seat, step, muffler etc.

Muffler

◯The muffler and muffler stay were made by the owner who is a welder.


Seat

◯A one-off seat for seat rail drop. The seat rail drop process involves bending the down tube forward, resulting in an even lower down than usual. We are committed to precision, strength, and durability in our production.


Electrical Equipment

IC blinker relay wide range specification

〇A wide-range blinker relay that can easily be used with LED blinkers, supporting 1-150 watts. It can also be used as a replacement for the original relay.

Battery Lesser

〇This is a battery-less kit that is made entirely in Japan.


Gasoline Tank Installation

◯ One-off gas tank.

Welding nut non-through M8 2p

〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

Weld tab M size 4.5mm thickness 2p

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

Weld tab L size 4.5mm thick steel 2p

〇 Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.


Drive System

Front sprocket SR400/500 428-19

〇A durable replacement sprocket made of steel.


  • RearFenders, rear shocks, swingarms, etc.

    Rear Wheel

    16″ Kit Steel Spoke SR400/500 Rear

    〇A kit that gives a powerful look with the same size as a typical Harley. It increases the range of tire choices.

    LOADSTAR TIRE 5.00-16

    〇A classic vintage-style tire.


    Rear Fender

    ◯The owner also performed the narrowing of the Fat Bob rear fender.


    Rear Blinker

    Small Bullet Turn Signal Chrome 4pcs SET General Purpose

    〇A classic among classics. A chopper-style blinker.

    Weld tab S size 4.5mm thick steel 2p

    〇Welded onto a hardtail. Used as a blinker base.


    Drive System

    Rear sprocket SR400/500 428-56

    〇An affordable and durable replacement sprocket.

    O-ring chain 428-130L

    〇A replacement drive chain with built-in O-rings.

    ※Parts Reference may show similar products or products with additional processing.