FrontHandlebars, F forks, headlights, etc.

【Front Fork】

◯The front fork has been lowered by 3cm.

【Front Fender】

“2%er Short Front Fender STD [SR400/500]“

〇A short fender that suits any style. Despite being made of FRP, it has a design with ribs around the perimeter like the original.

【Front Wheel】

“Front 19 Inch Kit SR400/500 for Drum“

◯The front wheel is 19 inches.

【Headlight】

“4.5-inch Bates Light Chrome General Purpose“

“SR Bottom Mount Light Stay“

〇It is installed with a headlight stay that is mounted low and close to the vehicle body.

【Handle/Handle Area】

◯A custom handle tailored to the owner’s physique.

“Amal type throttle holder, general purpose (for 7/8″)“

“Amal type slot wire 1200mm ’88~’08“

“300mm Long Brake Cable“

“200mm Long Clutch Cable“

〇We use long cables for the simple throttle.

“Handle Lock Weld On Kit“

〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style blinker.

『SR400/500 Bottom Mount narrow blinker stay』

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

『Mechanical Speedometer 60mm Black Panel 1:4』

『Universal Speedometer Stay』

〇Mounted on the less noticeable and highly visible front left side of the gasoline tank.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“One-off Pipe Manufacturing Exhaust Pipe Flange Set”

〇A one-off made using a convenient manufacturing kit for the mouthpiece at the root. A rough shotgun muffler. The volume is kept quite low as per the owner’s request.

【Seat/Seat Rail】

◯Our standard seat rail drop processing is done with a focus on design, planning, precision, strength, torsional rigidity during curve entry, and durability. We use thick pipe material (1.5 times the original) and carefully align the surfaces by hand bending, then deeply join them with TIG welding.

【Electrical Equipment】

“IC blinker relay wide range specification“

〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.

“Battery Lesser“

〇A battery-less kit that is made entirely in Japan.

【Gasoline Tank Installation】

◯ Egg tank is mounted with three-point rubber. The capacity is 7 liters.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also enlarges the hole diameter and uses it as a rubber mount.

【Engine Area】

“Breather filter SR400/500“

〇A filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Shock】

“280mm G-Suspension/Chrome”

〇A rear shock that lowers by about 4cm. It moves well among low-down suspensions. (Removal of the original chain case is necessary)

【Rear Wheel】

『16″ Kit Steel Spoke SR400/500 Rear』

〇This is a kit that gives a powerful look with the same size as a typical Harley. Uses DURO-made GOODYEAR pattern tires.

『Drilled plate torque rod SR400/500』

〇This is a drilled design torque rod to avoid interference with the wider tires.

【Rear Fender】

◯The short bob fender, a staple of compact choppers, is a one-off modification for Harley. It is mounted in such a way that it does not bear the rider’s weight, reducing the load on the fender.

【Rear Blinker】

『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』

〇A classic among classics. A chopper-style blinker.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇A durable sprocket made of steel.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.