#13 SR400Custom Report
A standard street chopper.
This is a custom based on the “Bobber/Compact Chopper Complete”.
The silver leaf × lettering on the tank was requested from “Baroque Bank$”.
Custom List
FrontHandlebars, F forks, headlights, etc.
【Front Fork】
〇Classic universal fork boots.
【Front Tire】
〇A classic watermelon pattern, high vintage style tire.
【Headlight】
“5.75 inch Bates Light Black Body/Chrome Rim”
〇A classic headlight that matches well with the SR’s vehicle size and fork width. It is installed with a headlight stay that mounts low and close to the vehicle body.
【Handle/Handle Area】
〇A narrow flat handle with a short clamp section.
“Amal type throttle holder, general purpose (for 7/8″)“
“Chopper Grip Black 22.2mm 7/8inch“
“Amal type slot wire 1000mm ’88~’08“
“Brake wire/100mm 200mm 300mm 600mm SR400/500 #SR400/500“
“Clutch wire/300mm 200mm 100mm standard SR400/500 ALL YEARS“
〇We use each cable for a simple throttle.
〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.
“MOTOR ROCK Decompression lever“
〇 A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)
【Front Blinker】
“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
“SR400/500 Bottom Mount narrow blinker stay“
〇A stay to attach a 10mm blinker to the bottom of the frame.
【Speedometer】
“Mechanical Speedometer 60mm Black Panel 1:4“
〇Mounted on the left front side of the gasoline tank, where it is inconspicuous and highly visible.
CenterTank, oil tank, seat, step, muffler etc.
【Muffler】
◯One-off muffler.
【Step】
“Mid-High Control Parkerized for SR400/500“
〇This step kit is essential for 2%ER’s custom, which makes your riding posture cool and extremely less tiring.
【Electrical】
“IC blinker relay wide range specification“
〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.
〇This is a battery-less kit that is made entirely in Japan.
“Custom Ignition Switch Weld On Kit General Purpose“
〇Easy to operate even while riding, it is welded and installed under the left side of the seat.
【Gasoline Tank Installation】
◯ Narrow Mustang tank, 3-point rubber mount.
“Welding nut non-through M8 2p“
〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.
“Weld tab M size 4.5mm thickness 2p“
〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.
“Weld tab L size 4.5mm thick steel 2p“
〇 Used for the rear attachment of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.
【Engine Area】
〇This is a filter kit needed when removing the original air cleaner.
【Drive System】
“Front sprocket SR400/500 428-19“
● A durable replacement sprocket made of steel.
RearFenders, rear shocks, swingarms, etc.
【Rear Shock】
〇A rear shock that lowers by about 4cm. It moves well among low-down suspensions. (Removal of the original chain case is necessary)
【Rear Tire】
〇A classic vintage style watermelon pattern. It’s a rear tire with height and volume.
【Rear Fender】
“5-Inch Custom Rib Fender – Steel Material“
“Reinforcement Back Plate for 5-Inch Rib Fender“
〇A thick and durable rib fender. A reinforcement plate is added around the mounting holes to mount it even more robustly.
【Rear Blinker】
『Small Bullet Turn Signal Chrome 4pcs SET General Purpose』
〇A classic among classics. A chopper-style blinker.
『Rear Bottom Mount Blinker Stay』
〇A stay to attach the blinker to the swing arm.
【Drive System】
“Rear sprocket SR400/500 428-56“
〇A durable sprocket made of steel.
〇A replacement drive chain with built-in O-rings.
※Parts Reference may show similar products or products with additional processing.