FrontHandlebars, F forks, headlights, etc.

【Front Fork】

◯The front fork is lowered. It is designed and constructed to maintain good movement and prevent bottoming out.

【Front Tire】

【LOADSTAR TIRE 4.00-18】

◯A classic watermelon pattern, this is a vintage style tire with height.

【Headlight】

“7 inch Lucas Type Headlight Case Black“

〇A standard 7-inch diameter, bullet-shaped headlight case (painted) in the cafe racer style. The light stay is drilled from WM made.

【Handle/Handle Area】

“2%er Top Bridge Ⅰ for separate handle [SR400/500]“

◯ A classic style top bridge without a post hole for the bar handle. The stays are smoothed and buffed for a simple finish.

“2%er Stainless Steel Separate Handle“

〇 High-quality separate handle. It was designed to resemble the 1960s Tomazeli style and fits well with cafe racers.

“Amal type throttle holder, general purpose (for 7/8″)“

〇 A very simple, classic vintage style throttle.

“Amal type slot wire 900mm ’88~’08“

“Brake wire/100mm 200mm 300mm 600mm SR400/500 #SR400/500“

“Clutch wire/300mm 200mm 100mm standard SR400/500 ALL YEARS“

“Handle Lock Weld On Kit“

〇We have newly installed a handle lock under the stem, which is inconspicuous and easy to operate.

“MOTOR ROCK Decompression lever“

A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)

【Front Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“SR400/500 Bottom Mount narrow blinker stay“

〇A stay to attach a 10mm blinker to the bottom of the frame.

【Speedometer】

” Inside meter kit for drum brake SR400/500 #2%er Original #SR400/500“

◯ It’s a speedometer kit that doesn’t stand out without ruining the style, but has good visibility while riding.

CenterTank, oil tank, seat, step, muffler etc.

【Muffler】

“Fishtail End Tip“

◯The short fishtail muffler is one-off. Added drilled processing.

【Step】

“Mid-High Control Parkerized for SR400/500“

〇This step kit is indispensable for 2%ER’s custom that makes your riding posture cool and extremely less tiring. This vehicle is equipped with a one-off machined peg.

【Sheet】

◯The sheet is 70’s deadstock.

【Gasoline Tank Installation】

◯ A one-off tank with a normal tank processed into A, J, S style, center rib processing, and a relocated Harley cap to match the style.

“Welding nut non-through M8 2p“

〇 Drill a hole in the gasoline tank body and weld it in. It’s non-penetrating, so it won’t leak. Used on both sides.

“Weld tab M size 4.5mm thickness 2p“

〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.

“Weld tab L size 4.5mm thick steel 2p“

〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.

【Electrical Equipment】

“Brat Style Electrical Plate“

〇A simple electrical plate that makes it easy to organize harnesses and electrical components.

“IC blinker relay wide range specification“

〇A wide-range turn signal relay that can be used without difficulty even with LED turn signals. It supports 1-150 watts and can also be used as a replacement for the original relay.

“Battery Lesser“

〇This is a battery-less kit that we manufacture in Japan.

“Custom Ignition Switch Weld On Kit General Purpose“

〇The main key, which is originally attached to the top bridge, can be easily operated even while riding, and is welded and installed on the lower left of the seat.

【Engine Area】

“Breather filter SR400/500“

〇This is a filter kit needed when removing the original air cleaner.

【Drive System】

“Front sprocket SR400/500 428-19“

〇A durable replacement sprocket made of steel.

RearFenders, rear shocks, swingarms, etc.

【Rear Wheel】

“16″ Kit Steel Spoke SR400/500 Rear“

〇This is a kit that gives a powerful look with the same size as a typical Harley.

“LOADSTAR TIRE　5.00-16“

〇A classic vintage-style tire.

“Drilled plate torque rod SR400/500“

〇A drilled design torque rod to avoid interference with the wider tire.

【Rear Shock】

“280mm G-Suspension/Black”

●A rear shock that lowers by about 4cm. It moves well among low-down suspensions.

【Rear Fender】

◯Cut the rear frame and attach a one-off short fender.

【Rear Blinker】

“Small Bullet Turn Signal Chrome 4pcs SET General Purpose“

〇A classic among classics. A chopper-style blinker.

“Weld tab S size 4.5mm thick steel 2p“

〇Welded onto a hardtail. Used as a blinker base.

【Drive System】

“Rear sprocket SR400/500 428-56“

〇An affordable and durable replacement sprocket.

“O-ring chain 428-130L“

〇A replacement drive chain with built-in O-rings.