#60 SR400Custom Report
A great deal on a complete setup, standard compact chopper. (Additional option for one-off seat only)
Designed with attention to easy handling and good cushioning, even for small women owners who love long touring.
We have produced it reflecting the preferences of each owner.

For more, “Click here for Bobber/Chopper Complete“
Custom List
FrontHandlebars, F forks, headlights, etc.
【Front Tire】
◯ A classic watermelon pattern, a vintage style tire with height.
【Headlight】
“4.5-inch Bates Light Chrome General Purpose“
〇It is installed with a headlight stay that is mounted low and close to the vehicle body.
【Handle/Handle Area】
◯A custom handle tailored to the owner’s physique.
“Amal type throttle holder, general purpose (for 7/8″)“
“Amal type slot wire 1200mm ’88~’08“
〇We use long cables for the simple throttle.
〇It is newly installed by welding to the lower part of the stem, which is inconspicuous and easy to operate.
“MOTOR ROCK Decompression lever“
A decompression lever directly attached to the engine to simplify the area around the handle. (The one on the vehicle is an old model)
【Front Blinker】
“Small Bullet Turn Signal Matte Black 4pcs SET General Purpose“
〇A classic among classics. A chopper-style blinker.
【Speedometer】
『Mechanical Speedometer 60mm Black Panel 1:4』
〇Mounted on the less noticeable and highly visible front left side of the gasoline tank.
CenterTank, oil tank, seat, step, muffler etc.
【Muffler】
◯The muffler is a standard setting drag pipe.
【Seat/Seat Rail】
◯Custom-made seat. Seat rail drop processing. We will design the bending position, angle, etc. according to the overall balance that is considered ideal.
【Electrical Equipment】
“IC blinker relay wide range specification“
〇A wide-range blinker relay that can handle 1-150 watts without any problem, even for LED blinkers. It can also be used as a replacement for the original relay.
〇A battery-less kit that is manufactured entirely in Japan.
“Custom ignition switch bolt-on kit General-purpose“
〇The main key, which is originally attached to the top bridge, is easy to operate even while riding, and is installed on the lower right of the seat.
【Gasoline Tank Installation】
◯ A one-off gas tank using an egg tank.
『Welding nut non-through M8 2p』
〇 Drill a hole in the gasoline tank body and insert and weld. It’s non-penetrating, so it won’t leak. Used on both sides.
『Weld tab M size 4.5mm thickness 2p』
〇 Enlarge the hole diameter and change to a rubber mount specification to hold the non-penetrating nut. Used on both sides.
『Weld tab L size 4.5mm thick steel 2p』
〇 Used for the rear installation of the gas tank. This also has an enlarged hole diameter and is used with a rubber mount.
【Engine Area】
〇A filter kit needed when removing the original air cleaner.
【Drive System】
“Front sprocket SR400/500 428-19“
〇A durable replacement sprocket made of steel.
RearFenders, rear shocks, swingarms, etc.
【Rear Tire】
〇A classic vintage style watermelon pattern. It’s a rear tire with height and volume.
【Rear Shock】
●A rear shock that is about 4cm lower. It moves well among low-down suspensions.
【Rear Fender】
◯Custom-made rear fender. We will securely install it in a position of your preference, or in a balanced position that we recommend.
【Rear Turn Signal】
Small Bullet Turn Signal Matte Black 4pcs SET General Purpose
〇A classic among classics. A chopper-style turn signal.
“Rear Bottom Mount Turn Signal Stay”
〇A stay to attach the turn signal to the swing arm.
【Drive System】
“Rear sprocket SR400/500 428-56“
〇A durable sprocket made of steel.
〇A replacement drive chain with built-in O-rings.
※Parts Reference may show similar products or products with additional processing.